- 您现在的位置：买卖IC网 > PDF目录176103 > ISL6227CA (INTERSIL CORP) Dual Mobile-Friendly PWM Controller with DDR Option PDF资料下载
参数资料
| 型号： | ISL6227CA |
| 厂商： | INTERSIL CORP |
| 元件分类： | 稳压器 |
| 英文描述： | Dual Mobile-Friendly PWM Controller with DDR Option |
| 中文描述： | DUAL SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封装： | 0.150 INCH, PLASTIC, SSOP-28 |
| 文件页数： | 6/27页 |
| 文件大小： | 834K |
| 代理商： | ISL6227CA |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
14
FN9094.7
May 4, 2009
Theory of Operation
Operation
The ISL6227 is a dual channel PWM controller intended for
use in power supplies for graphic chipsets, SDRAM, DDR
DRAM, or other low voltage power applications in modern
notebook and sub-notebook PCs. The IC integrates two
control circuits for two synchronous buck converters. The
output voltage of each controller can be set in the range of
0.9V to 5.5V by an external resistive divider.
The synchronous buck converters can operate from either
an unregulated DC source, such as a notebook battery, with
a voltage ranging from 5.0V to 28V, or from a regulated
system rail of 3.3V or 5V. In either operational mode the
controller is biased from the +5V source.
The controllers operate in the current mode with input
voltage feed-forward which simplifies feedback loop
compensation and rejects input voltage variation. An
integrated feedback loop compensation dramatically
reduces the number of external components.
Depending on the load level, converters can operate either
in a fixed 300kHz frequency mode or in a HYS mode.
Switch-over to the HYS mode of operation at light loads
improves converter efficiency and prolongs battery life. The
HYS mode of operation can be inhibited independently for
each channel if a variable frequency operation is not
desired.
The ISL6227 has a special means to rearrange its internal
architecture into a complete DDR solution. When the DDR
pin is set high, the second channel can provide the capability
to track the output voltage of the first channel. The buffered
reference voltage required by DDR memory chips is also
provided.
Initialization
The ISL6227 initializes if at least one of the enable pins is
set high. The Power-On Reset (POR) function continually
monitors the bias supply voltage on the VCC pin, and
initiates soft-start operation when EN1 or EN2 is high after
the input supply voltage exceeds 4.45V. Should this voltage
drop lower than 4.14V, the POR disables the chip.
Soft-Start
When soft-start is initiated, the voltage on the SOFT pin of
the enabled channel starts to ramp up gradually with the
internal 4.5A current charging the soft-start capacitor. The
output voltage follows the soft-start voltage with the
converter operating at 300kHz PWM switching frequency.
When the SOFT pin voltage reaches 0.9V, the output voltage
comes into regulation, (see block diagram). When the SOFT
voltage reaches 1.5V, the power good (PGOOD) and the
mode control is enabled. The soft-start process is depicted in
Even though the soft-start pin voltage continues to rise after
reaching 1.5V, this voltage does not affect the output
voltage. During the soft-start, the converter always operates
in continuous conduction mode independent of the load level
or VOUT pin connection.
The soft-start time (the time from the moment when EN
becomes high to the moment when PGOOD is reported) is
determined by Equation 1:
The time it takes the output voltage to come into regulation
can be obtained from Equation 2:
During soft-start stage before the PGOOD pin is ready, the
undervoltage protection is prohibited. The overvoltage and
overcurrent protection functions are enabled.
If the output capacitor has residue voltage before startup,
both lower and upper MOSFETs are in off-state until the
soft-start capacitor charges equal the VSEN pin voltage.
This will ensure the output voltage starts from its existing
voltage level.
Ch3 1.0V
Ch2 2.0V
Ch4 5.0V
M1.00ms
Ch1 5.0V
3
2
4
1
EN
0.9V
1.5V
SOFT
VOUT
PGOOD
FIGURE 33. START-UP
t
SOFT
1.5V
Csoft
×
4.5
μA
----------------------------------
=
(EQ. 1)
t
RISE
0.6
t
SOFT
×
=
(EQ. 2)
ISL6227
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6227CA-T | Dual Mobile-Friendly PWM Controller with DDR Option |
| ISL6227CAZ | Dual Mobile-Friendly PWM Controller with DDR Option |
| ISL6227CAZ-T | Dual Mobile-Friendly PWM Controller with DDR Option |
| ISL6227 | Dual Mobile-Friendly PWM Controller with DDR Option |
| ISL6292DCRZ-T | Li-ion/Li Polymer Battery Charger |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6227CA-T | 功能描述:IC CONTROLLER DDR, DDR2 28QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6227CAZ | 功能描述:电流型 PWM 控制器 VER OF ISL6227CA RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6227CAZS2698 | 功能描述:IC CONTROLLER DDR, DDR2 28QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6227CAZ-T | 功能描述:电流型 PWM 控制器 VER OF ISL6227CA-T RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6227CAZ-TS2698 | 功能描述:IC CONTROLLER DDR, DDR2 28QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。