参数资料
| 型号： | ISL6227IRZ |
| 厂商： | Intersil |
| 文件页数： | 19/27页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER DDR, DDR2 28QFN |
| 标准包装： | 60 |
| 应用： | 控制器，DDR，DDR2 |
| 输入电压： | 5 V ~ 28 V |
| 输出数： | 2 |
| 输出电压： | 0.9 V ~ 5.5 V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-VFQFN 裸露焊盘 |
| 供应商设备封装： | 28-QFN 裸露焊盘（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页
ISL6227
Voltage Monitor and Protections
The converter output is monitored and protected against
extreme overload, short circuit, overvoltage, and
undervoltage conditions. A sustained overload on the output
sets the PGOOD low and latches off the offending channel of
first eight clock cycles, normal operation is restored and the
overcurrent circuit resets itself at the end of sixteenth clock
cycles; see Figure 40.
the chip. The controller operation can be restored by cycling
the VCC voltage or toggling both enable (EN) pins to low to
1
IL
PGOO D
8 CLK
clear the latch.
Power Good
In the soft-start process, the PGOOD is established after the
soft pin voltage is at 1.5V. In normal operation, the PGOOD
window is 100mV below the 0.9V and 135mV higher than
2
3
VOUT
SHUTDOWN
0.9V. The VSEN pin has to stay within this window for
PGOOD to be high. Since the VSEN pin is used for both
Ch1 5.0V
Ch3 1.0A Ω
Ch2 100mV
M 10.0 μ s
feedback and monitoring purposes, the output voltage
deviation can be coupled directly to the VSEN pin by the
capacitor in parallel with the voltage divider as shown in
Figure 4. In order to prevent false PGOOD drop, capacitors
need to parallel at the output to confine the voltage deviation
with severe load step transient. The PGOOD comparator
has a built-in 3μs filter. PGOOD is an open drain output.
Overcurrent Protection
In dual switcher application, both PWM controllers use the
lower MOSFETs on-resistance r DS(ON), to monitor the
current for protection against shorted outputs. The sensed
FIGURE 40. OVERCURRENT PROTECTION
Due to the nature of the used current sensing technique,
and to accommodate a wide range of the r DS(ON) variation,
the value of the overcurrent threshold should set at about
180% of the nominal load value. If more accurate current
protection is desired, a current sense resistor placed in
series with the lower MOSFET source may be used. The
inductor current going through the lower MOSFET is sensed
and held at 400ns after the upper MOSFET is turned off;
therefore, the sensed current is very close to its peak value.
The inductor peak current can be written as Equation 16:
2L o ? F SW ? V IN
current from the ISEN pin is compared with a current set by
a resistor connected from the OCSET pin to ground:
( V IN – V o ) ? V o
I peak = -------------------------------------------- + I load
(EQ.16)
R SET = ---------------------------------------------------------
I OC ? r DS ( ON )
R CS + 140 Ω
10.3V
-------------------------------------- + 8 μ A
(EQ.15)
As seen from Equation 16, the inductor peak current
changes with the input voltage and the inductor value once
an output voltage is selected.
where, I OC is a desired overcurrent protection threshold and
R CS is the value of the current sense resistor connected to
the ISEN pin. The 8μA is the offset current added on top of
the sensed current from the ISEN pin for internal circuit
After overcurrent protection is activated, there are two ways
to bring the offending channel back: (1) Both EN1 and EN2
have to be held low to clear the latch, (2) To recycle the VCC
of the chip, the POR will clear the latch.
biasing.
Undervoltage Protection
If the lower MOSFET current exceeds the overcurrent
threshold, a pulse skipping circuit is activated. The upper
MOSFET will not be turned on and the lower MOSFET
keeps conducting as long as the sampled current is higher
than the threshold value, limiting the current supplied by the
DC voltage source. The current in the lower MOSFET will be
sampled at the internal 300kHz oscillator frequency and
monitored. When the sampled current is lower than the OC
threshold value, the following UGATE pulse will be released
and it allows turning on the upper MOSFET based on the
voltage regulation loop. This kind of operation remains for
eight clock cycles after the overcurrent comparator was
tripped for the first time. If after the first eight clock cycles the
sampled current exceeds the overcurrent threshold again,
within a time interval of another eight clock cycles, the
overcurrent protection latches and disables the offending
channel. If the overcurrent condition goes away during the
19
In the process of operation, if a short circuit occurs, the output
voltage will drop quickly. Before the overcurrent protection
circuit responds, the output voltage will fall out of the required
regulation range. The chip comes with undervoltage protection.
If a load step is strong enough to pull the output voltage lower
than the undervoltage threshold, the offending channel latches
off immediately. The undervoltage threshold is 75% of the
nominal output voltage. Toggling both pins to low, or recycling
VCC, will clear the latch and bring the chip back to operation.
Overvoltage Protection
Should the output voltage increase over 115% of the normal
value due to the upper MOSFET failure, or for other reasons,
the overvoltage protection comparator will force the
synchronous rectifier gate driver high. This action actively
pulls down the output voltage and eventually attempts to
blow the battery fuse. As soon as the output voltage is within
FN9094.7
May 4, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| 80MXC5600MEFCSN35X40 | CAP ALUM 5600UF 80V 20% SNAP-IN |
| EL5126CLZ-T13 | IC VOLTAGE GEN 8CH TFT-LCD 32QFN |
| 250MXC1000MEFCSN35X35 | CAP ALUM 1000UF 250V 20% SNAP-IN |
| EL5126CLZ-T7 | IC VOLTAGE GEN 8CH TFT-LCD 32QFN |
| 400SXC330MEFCSN30X45 | CAP ALUM 330UF 400V 20% SNAP-IN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6227IRZ-T | 功能描述:IC CONTROLLER DDR, DDR2 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6228 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Performance Dual-Output Buck Controller for Notebook Applications |
| ISL6228EVAL3Z | 功能描述:EVALUATION BOARD FOR ISL6228 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6228HIEVAL3Z | 功能描述:EVALUATION BOARD FOR ISL6228HI RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6228HRTZ | 功能描述:IC REG CTRLR BUCK PWM 28-TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。