参数资料
| 型号： | ISL6264CRZ |
| 厂商： | Intersil |
| 文件页数： | 16/23页 |
| 文件大小： | 0K |
| 描述： | IC CORE CTRLR TWO-PHASE 40-QFN |
| 标准包装： | 50 |
| 应用： | 控制器，AMD 移动式 Turion? |
| 输入电压： | 5 V ~ 24 V |
| 输出数： | 1 |
| 输出电压： | 0.38 V ~ 1.55 V |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN（6x6） |
| 包装： | 管件 |
ISL6264
TABLE 2.
Dynamic Operation
PSI_L = LOGIC HIGH
PSI_L = LOGIC LOW
The ISL6264 responds to changes in VID command voltage
Operation
2-CCM
1-DE (diode emulation)
by slewing to new voltages with a dV/dt set by the SOFT
capacitor. The internal current source of 230μA is used to
Smooth mode transitions are facilitated by the R3
Technology ? , which correctly maintains the internally
synthesized ripple currents throughout mode transitions. The
regulator is thus able to deliver the appropriate current to the
load throughout mode transitions. The controller contains
embedded mode-transition algorithms which robustly
maintain voltage-regulation for all control signal input
sequences and durations.
Mode-transition sequences will often occur in concert with VID
changes; therefore the timing of the mode transition of
ISL6264 has been carefully designed to work in concert with
VID changes. For example, transitions into single-phase
mode if PSI_L and VID toggles at the same time will be
delayed until the VID induced voltage ramp is complete, to
allow the associated output capacitor charging current is
shared by both inductor paths. While in single-phase
automatic-DCM mode with PSI_L = logic low, VID changes
will initiate an immediate return to two-phase CCM mode
during the VID transition. This ensures that both inductor
paths share the output capacitor charging current and are fully
active for the subsequent load current increases.
The controller contains internal counters which prevent
spurious control signal glitches from resulting in unwanted
mode transitions. Control signals of less than two switching
periods do not result in phase-idling. Signals of less than
seven switching periods do not result in implementation of
automatic-DCM mode.
While transitioning to single-phase operation, the controller
smoothly transitions current from the idling-phase to the
active-phase, and detects the idling-phase zero-current
condition. During transitions into automatic-DCM or
forced-CCM mode, the timing is carefully adjusted to eliminate
charge or discharge the SOFT capacitor.
Intersil's R 3 Technology ? has intrinsic voltage feed forward.
As a result, high-speed input voltage steps do not result in
significant output voltage perturbations. In response to load
current step increases, the ISL6264 will transiently raise the
switching frequency so that response time is decreased and
current is shared by two channels.
Protection
The ISL6264 provides overcurrent, overvoltage, and
undervoltage protection as shown in Table 3.
Overcurrent protection is tied to the voltage droop which is
determined by the resistors selected as described in the
After the load-line is set, the OCSET resistor can be selected
to detect overcurrent at any level of droop voltage. An
overcurrent fault will occur when the load current exceeds
the overcurrent setpoint voltage while the regulator is in a
2-phase mode. While the regulator is in a 1-phase mode of
operation, the overcurrent setpoint is automatically reduced
by half. For overcurrents less than 2.5 times the OCSET
level, the over-load condition must exist for 120μs in order to
trip the OC fault latch.
For overloads exceeding 2.5 times the set level, the PWM
outputs will immediately shut off and PGOOD will go low to
maximize protection due to hard shorts.
In addition, excessive phase unbalance, for example, due to
gate driver failure, will be detected in two-phase operation
and the controller will be shut-down after one millisecond's
detection of the excessive phase current unbalance. The
phase unbalance is detected by the voltage on the ISEN
pins if the difference is greater than 9mV.
output voltage excursions. When a phase is added, the
current balance between phases is quickly restored.
TABLE 3. FAULT-PROTECTION SUMMARY OF ISL6264
FAULT DUATION
PRIOR TO
PROTECTION
PROTECTION ACTIONS
FAULT RESET
Overcurrent fault
Way-Overcurrent fault
Overvoltage fault (1.8V)
120μs
<2μs
immediately
PWM1, PWM2 three-state, PGOOD latched low
PWM1, PWM2 three-state, PGOOD latched low
Low-side FET on until Vcore <0.85V, then PWMs
VR_ON toggle or VDD toggle
VR_ON toggle or VDD toggle
VDD toggle
three-state, PGOOD latched low (OV-1.8V always)
Overvoltage fault (+200mV)
1ms
ISL6264 still tries to regulate V CORE , PGOOD latched low VR_ON toggle or VDD toggle
Undervoltage fault (-300mV)
Unbalance fault (9mV)
16
1ms
1ms
PWM1, PWM2 three-state, PGOOD latched low
PWM1, PWM2 three-state, PGOOD latched low
VR_ON toggle or VDD toggle
VR_ON toggle or VDD toggle
FN6359.3
May 28, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6265AHRTZ-T | IC CTRLR MULTI-OUTPUT 48-TQFN |
| ISL6265CHRTZ | IC CTRLR MULTI-OUTPUT 48TQFN |
| ISL6265HRTZ-T | IC CTLR MULTI-OUTPUT 48-TQFN |
| ISL6266AHRZ | IC CORE CTRLR 2PHASE 48-QFN |
| ISL6267HRZ | IC PWM CTRLR MULTIPHASE 48TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6264CRZ-T | 功能描述:IC CORE CTRLR TWO-PHASE 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6265 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Multi-Output Controller with Integrated MOSFET Drivers for AMD SVI Capable |
| ISL6265A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Multi-Output Controller with Integrated MOSFET Drivers for AMD SVI Capable Mobile CPUs |
| ISL6265AHRTZ | 功能描述:电流型 PWM 控制器 MULTI-OUTPUT CNTRLRS PHS W/EMBEDDED GATE RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6265AHRTZ-T | 功能描述:电流型 PWM 控制器 MULTI-OUTPUT CNTRLRS PHS W/EMBEDDED GATE RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。