参数资料
| 型号： | ISL6264CRZ |
| 厂商： | Intersil |
| 文件页数： | 17/23页 |
| 文件大小： | 0K |
| 描述： | IC CORE CTRLR TWO-PHASE 40-QFN |
| 标准包装： | 50 |
| 应用： | 控制器，AMD 移动式 Turion? |
| 输入电压： | 5 V ~ 24 V |
| 输出数： | 1 |
| 输出电压： | 0.38 V ~ 1.55 V |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN（6x6） |
| 包装： | 管件 |
ISL6264
Undervoltage protection is independent of the overcurrent
OFFSET ≡ ---------------- R CIN
(EQ. 1)
limit. If the output voltage is less than the VID set value by
300mV or more, a fault will latch after one millisecond in that
condition. The PWM outputs will turn off and PGOOD will go
low. Note that most practical core regulators will have the
overcurrent set to trip before the -300mV undervoltage limit.
There are two levels of overvoltage protection and response.
For output voltage exceeding the set value by +200mV for
1ms, a fault is declared. All of the above faults have the
same action taken except 200mV overvoltage fault: PGOOD
is latched low and the upper and lower power FETs are
turned off so that inductor current will decay through the FET
body diodes. This condition can be reset by bringing VR_ON
low or by bringing VDD below 4V. When these inputs are
returned to their high operating levels, a soft-start will occur.
Under 200mV overvoltage fault, PGOOD is latched low but
the ISL6264 still tries to regulate the output voltage.
The second level of overvoltage protection behaves
differently. If the output exceeds 1.8V, an OV fault is
immediately declared, PGOOD is latched low and the
low-side FETs are turned on. The low-side FETs will remain
on until the output voltage is pulled down below about 0.85V
at which time all FETs are turned off. If the output again rises
above 1.7V, the protection process is repeated. This affords
the maximum amount of protection against a shorted
high-side FET while preventing output ringing below ground.
The 1.8V OV is not reset with VR_ON, but requires that VDD
be lowered to reset. The 1.8V OV detector is active at all
times that the controller is enabled including after one of the
other faults occurs so that the processor is protected against
high-side FET leakage while the FETs are commanded off.
1.2V
R OFS
Normally we chose RCIN as 1k Ω for the convenience of
design, then ROFS of 36.5k Ω will result in a positive
OFFSET voltage of 33mV.
Component Selection and Application
Soft-Start and VID Transition Slew Rates
The ISL6264 uses two different slew rates for start-up and
the normal operation mode. The first is a slow slew rate in
order to reduce inrush current during start-up. Note that the
SOFT cap current is bidirectional. The current is flowing into
the SOFT capacitor when the output voltage is commanded
to rise, and out of the SOFT capacitor when the output
voltage is commanded to fall.
The two slew rates are determined by commanding one of
two current sources onto the SOFT pin. As can be seen in
Figure 30, the SOFT pin has a capacitance to ground. Also,
the SOFT pin is the input to the error amplifier and is,
therefore, the commanded system voltage. Depending on
the state of the system, i.e. Start-Up or After Start-up, one of
the two currents shown in Figure 30 will be used to charge or
discharge this capacitor, thereby controlling the slew rate of
the commanded voltage. These currents can be found under
the “Soft-Start Current“ section of theTable Electrical
ISL6264
Offset Voltage
I SS
I2
ERROR
AMPLIFIER
The reference voltage at OFS pin is 1.2V. A resistor (ROFS)
connecting the OFS pin to GND will setup a current flowing
out of OFS pin. This current is internally mirrored out of FB
pin. Therefore, a voltage drop is established across the
resistor between FB and VDIFF pin. For the convenience of
illustration, name the compensation network resistor
SOFT
+
+
between FB and VDIFF as R CIN .
CSOFT
VREF
V O (V)
FIGURE 30. SOFT PIN CURRENT SOURCES FOR FAST AND
SLOW SLEW RATES
OFFSET
0
VID
I O (A)
The first current, labelled I SS , is given in the Specification
Table as 43A. This current is used during Soft-Start. The
second current, I 2 sums with I SS to get the larger of the two
currents, labeled IGV in the Electrical Specification Table.
This total current is typically 210A with a minimum of 185A.
The symbol, SLEWRATE, will determine the choice of the
SOFT capacitor, CSOFT, by Equation 2:
C SOFT ≡ ------------------------------------
FIGURE 29. LOAD LINE AND OFFSET
17
I 2
SLEWRATE
(EQ. 2)
FN6359.3
May 28, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6265AHRTZ-T | IC CTRLR MULTI-OUTPUT 48-TQFN |
| ISL6265CHRTZ | IC CTRLR MULTI-OUTPUT 48TQFN |
| ISL6265HRTZ-T | IC CTLR MULTI-OUTPUT 48-TQFN |
| ISL6266AHRZ | IC CORE CTRLR 2PHASE 48-QFN |
| ISL6267HRZ | IC PWM CTRLR MULTIPHASE 48TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6264CRZ-T | 功能描述:IC CORE CTRLR TWO-PHASE 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6265 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Multi-Output Controller with Integrated MOSFET Drivers for AMD SVI Capable |
| ISL6265A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Multi-Output Controller with Integrated MOSFET Drivers for AMD SVI Capable Mobile CPUs |
| ISL6265AHRTZ | 功能描述:电流型 PWM 控制器 MULTI-OUTPUT CNTRLRS PHS W/EMBEDDED GATE RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6265AHRTZ-T | 功能描述:电流型 PWM 控制器 MULTI-OUTPUT CNTRLRS PHS W/EMBEDDED GATE RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。