参数资料
| 型号： | ISL62883IRTZ |
| 厂商： | Intersil |
| 文件页数： | 12/37页 |
| 文件大小： | 0K |
| 描述： | IC REG PWM 3PHASE BUCK 40TQFN |
| 标准包装： | 60 |
| 应用： | 控制器，Intel IMVP-6.5? |
| 输入电压： | 5 V ~ 21 V |
| 输出数： | 1 |
| 输出电压： | 0.013 V ~ 1.5 V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
ISL62883, ISL62883B
voltage V Crs hits VW, the slave circuit turns off the PWM pulse,
and the current source discharges C rs .
Since the ISL62883 works with V crs , which are large-amplitude
and noise-free synthesized signals, the ISL62883 achieves lower
phase jitter than conventional hysteretic mode and fixed PWM
mode controllers. Unlike conventional hysteretic mode
converters, the ISL62883 has an error amplifier that allows the
Vcrs
iL
CCM/DCM BOUNDARY
VW
controller to maintain a 0.5% output voltage accuracy.
Figure 5 shows the operation principles during load insertion
response. The COMP voltage rises during load insertion,
generating the master clock signal more quickly, so the PWM
pulses turn on earlier, increasing the effective switching
frequency, which allows for higher control loop bandwidth than
Vcrs
iL
VW
LIGHT DCM
conventional fixed frequency PWM controllers. The VW voltage
rises as the COMP voltage rises, making the PWM pulses wider.
During load release response, the COMP voltage falls. It takes
Vcrs
VW
DEEP DCM
the master clock circuit longer to generate the next master clock
signal so the PWM pulse is held off until needed. The VW voltage
falls as the VW voltage falls, reducing the current PWM pulse
width. This kind of behavior gives the ISL62883 excellent
response speed.
The fact that all the phases share the same VW window voltage
also ensures excellent dynamic current balance among phases.
Diode Emulation and Period Stretching
Phase
UG ATE
LG ATE
IL
FIGURE 6. DIODE EMULATION
ISL62883 can operate in diode emulation (DE) mode to improve
light load efficiency. In DE mode, the low-side MOSFET conducts
when the current is flowing from source to drain and doesn’t not
allow reverse current, emulating a diode. As Figure 6 shows, when
LGATE is on, the low-side MOSFET carries current, creating
negative voltage on the phase node due to the voltage drop across
the ON-resistance. The ISL62883 monitors the current through
monitoring the phase node voltage. It turns off LGATE when the
iL
FIGURE 7. PERIOD STRETCHING
Figure 7 shows the operation principle in diode emulation mode at
light load. The load gets incrementally lighter in the three cases
from top to bottom. The PWM on-time is determined by the VW
window size, therefore is the same, making the inductor current
triangle the same in the three cases. The ISL62883 clamps the
ripple capacitor voltage V crs in DE mode to make it mimic the
inductor current. It takes the COMP voltage longer to hit V crs ,
naturally stretching the switching period. The inductor current
triangles move further apart from each other such that the
inductor current average value is equal to the load current. The
reduced switching frequency helps increase light load efficiency.
Start-up Timing
With the controller's V DD voltage above the POR threshold, the
start-up sequence begins when VR_ON exceeds the 3.3V logic
high threshold. The ISL62883 uses digital soft start to ramp up
DAC to the boot voltage of 1.1V at about 2.5mV/μs. Once the
output voltage is within 10% of the boot voltage for 13 PWM
cycles (43μs for frequency = 300kHz), CLK_EN# is pulled low and
DAC slews at 5mV/μs to the voltage set by the VID pins. PGOOD
is asserted high in approximately 7ms. Figure 8 shows the typical
start-up timing. Similar results occur if VR_ON is tied to V DD , with
the soft-start sequence starting 120μs after V DD crosses the
POR threshold.
VDD
phase node voltage reaches zero to prevent the inductor current
from reversing the direction and creating unnecessary power loss.
If the load current is light enough, as Figure 6 shows, the inductor
VR_ON
5mV/μs
2.5mV/μs
90% VBOOT
VID
COMMAND
current will reach and stay at zero before the next phase node
pulse, and the regulator is in discontinuous conduction mode
(DCM). If the load current is heavy enough, the inductor current
will never reach 0A, and the regulator is in CCM although the
controller is in DE mode.
DAC
CLK_EN#
800μs
13 SWITCHING
CYCLES
VOLTAGE
~7ms
PGOOD
FIGURE 8. SOFT-START WAVEFORMS
12
FN6891.4
June 21, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6292BCRZ | IC CHARGER LI-ION 4.2V 4X4 16QFN |
| ISL6294IBZ | IC CHRGR LI-ION SGL 8-SOIC |
| ISL6306IRZ | IC REG CTRLR BUCK PWM VM 40-QFN |
| ISL6307AIRZ | IC REG CTRLR BUCK PWM VM 48-QFN |
| ISL6307BIRZ | IC REG CTRLR BUCK PWM VM 48-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL62883IRTZ-T | 功能描述:直流/直流开关调节器 3 PHS PWM BUCKG FOR MICROPROC PWR SUP RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL62884C | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Single-Phase PWM Regulator for IMVP-6a?￠ Mobile CPUs |
| ISL62884CEVAL2Z | 功能描述:EVAL BOARD FOR ISL62884C RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL62884CHRTZ | 功能描述:直流/直流开关调节器 1-PHS PWM BUCKG FOR MICROPROC PWR SUPPLY RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL62884CHRTZ-T | 功能描述:直流/直流开关调节器 1-PHS PWM BUCKG FOR MICROPROC PWR SUPPLY RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。