参数资料
| 型号： | ISL62883IRTZ |
| 厂商： | Intersil |
| 文件页数： | 17/37页 |
| 文件大小： | 0K |
| 描述： | IC REG PWM 3PHASE BUCK 40TQFN |
| 标准包装： | 60 |
| 应用： | 控制器，Intel IMVP-6.5? |
| 输入电压： | 5 V ~ 21 V |
| 输出数： | 1 |
| 输出电压： | 0.013 V ~ 1.5 V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
ISL62883, ISL62883B
Modes of Operation
TABLE 2. ISL62883 MODES OF OPERATION
OPERATIONAL
When the unfiltered version is 20mV below the filtered version,
the controller knows there is a fast voltage dip due to load
insertion, hence issues an additional master clock signal to
deliver a PWM pulse immediately.
CONFIGURATION
3-phase Configuration
2-phase Configuration
1-phase Configuration
PSI#
0
0
1
1
0
0
1
1
0
DPRSLPVR
0
1
0
1
0
1
0
1
0
MODE
2-phase CCM
1-phase DE
3-phase CCM
1-phase DE
1-phase CCM
1-phase DE
2-phase CCM
1-phase DE
1-phase CCM
The R 3 ? modulator intrinsically has voltage feed forward. The
output voltage is insensitive to a fast slew rate input voltage
change.
Protections
The ISL62883 provides overcurrent, current-balance,
undervoltage, overvoltage, and over-temperature protections.
The ISL62883 determines overcurrent protection (OCP) by
comparing the average value of the droop current I droop with an
internal current source threshold. It declares OCP when I droop is
above the threshold for 120μs. A resistor R comp from the COMP
pin to GND programs the OCP current source threshold, as Table 3
0 1 1-phase DE
1 0 1-phase CCM
1 1 1-phase DE
Table 2 shows the ISL62883 operational modes, programmed by
the logic status of the PSI# and the DPRSLPVR pins. In 3-phase
shows. It is recommended to use the nominal R comp value. The
ISL62883 detects the R comp value at the beginning of start up,
and sets the internal OCP threshold accordingly. It remembers the
R comp value until the VR_ON signal drops below the POR
threshold.
TABLE 3. ISL62883 OCP THRESHOLD
configuration, the ISL62883 enters 2-phase CCM for (PSI# = 0 and
DPRSLPVR = 0) by dropping PWM3 and operating phases 1 and 2
180° out-of-phase. It also reduces the overcurrent and the
way-overcurrent protection levels to 2/3 of the initial values. The
ISL62883 enters 1-phase DE mode when DPRSLPVR = 1. It drops
MIN. (k Ω )
R comp
NOMINAL
(k Ω )
none
MAX.
(k Ω )
none
OCP THRESHOLD (μA)
1-PHASE 2-PHASE 3-PHASE
MODE MODE MODE
20 40 60
phases 2 and 3, and reduces the overcurrent and the way-
overcurrent protection levels to 1/3 of the initial values.
In 2-phase configuration, the ISL62883 enters 1-phase CCM for
(PSI# = 0 and DPRSLPVR = 0). It drops Phase-2 and reduces the
overcurrent and the way-overcurrent protection levels to 1/2 of
the initial values. The ISL62883 enters 1-phase DE mode when
DPRSLPVR = 1 by dropping phase 2.
In 1-phase configuration, the ISL62883 does not change the
operational mode when the PSI# signal changes status. It enters
320
210
155
104
78
62
45
400
235
165
120
85
66
50
480
260
175
136
92
70
55
22.7
20.7
18
20
22.7
20.7
18
45.3
41.3
36
37.33
38.7
42.7
44
68
62
54
56
58
64
66
1-phase DE mode when DPRSLPVR = 1.
Dynamic Operation
The ISL62883 responds to VID changes by slewing to the new
voltage at 5mV/μs slew rate. As the output approaches the VID
command voltage, the dv/dt moderates to prevent overshoot.
Geyserville-III transitions commands one LSB VID step (12.5mV)
every 2.5μs, controlling the effective dv/dt at 5mv/μs. The
ISL62883 is capable of 5mV/μs slew rate.
When the ISL62883 is in DE mode, it will actively drive the output
voltage up when the VID changes to a higher value. It’ll resume
DE mode operation after reaching the new voltage level. If the
load is light enough to warrant DCM, it will enter DCM after the
inductor current has crossed zero for four consecutive cycles. The
ISL62883 will remain in DE mode when the VID changes to a
lower value. The output voltage will decay to the new value and
the load will determine the slew rate.
During load insertion response, the Fast Clock function increases
the PWM pulse response speed. The ISL62883 monitors the
VSEN pin voltage and compares it to 100ns - filtered version.
17
The default OCP threshold is the value when R comp is not
populated. It is recommended to scale the droop current I droop
such that the default OCP threshold gives approximately the
desired OCP level, then use R comp to fine tune the OCP level if
necessary.
For overcurrent conditions above 2.5 times the OCP level, the
PWM outputs will immediately shut off and PGOOD will go low to
maximize protection. This protection is also referred to as
way-overcurrent protection or fast-overcurrent protection, for
short-circuit protections.
The ISL62883 monitors the ISEN pin voltages to determine
current-balance protection. If the ISEN pin voltage difference is
greater than 9mV for 1ms, the controller will declare a fault and
latch off.
The ISL62883 will declare undervoltage (UV) fault and latch off if
the output voltage is less than the VID set value by 300mV or
more for 1ms. It’ll turn off the PWM outputs and dessert PGOOD.
The ISL62883 has two levels of overvoltage protections. The first
level of overvoltage protection is referred to as PGOOD
overvoltage protection. If the output voltage exceeds the VID set
FN6891.4
June 21, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6292BCRZ | IC CHARGER LI-ION 4.2V 4X4 16QFN |
| ISL6294IBZ | IC CHRGR LI-ION SGL 8-SOIC |
| ISL6306IRZ | IC REG CTRLR BUCK PWM VM 40-QFN |
| ISL6307AIRZ | IC REG CTRLR BUCK PWM VM 48-QFN |
| ISL6307BIRZ | IC REG CTRLR BUCK PWM VM 48-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL62883IRTZ-T | 功能描述:直流/直流开关调节器 3 PHS PWM BUCKG FOR MICROPROC PWR SUP RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL62884C | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Single-Phase PWM Regulator for IMVP-6a?￠ Mobile CPUs |
| ISL62884CEVAL2Z | 功能描述:EVAL BOARD FOR ISL62884C RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL62884CHRTZ | 功能描述:直流/直流开关调节器 1-PHS PWM BUCKG FOR MICROPROC PWR SUPPLY RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL62884CHRTZ-T | 功能描述:直流/直流开关调节器 1-PHS PWM BUCKG FOR MICROPROC PWR SUPPLY RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。