参数资料
| 型号： | ISL6314IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 20/32页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM 1PHASE BUCK 32-QFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 6,000 |
| 应用： | 控制器，Intel VR11，AMD CPU |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.38 V ~ 1.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
ISL6314
.
4. The VID code must not be 11111 in AMD 5-bit mode. This
ISL6314 INTERNAL CIRCUIT
EXTERNAL CIRCUIT
VCC
code signals the controller that no load is present. The
controller will not allow soft-start to begin if this VID code
is present on the VID pins.
Once all of these conditions are met the controller will begin
the soft-start sequence and will ramp the output voltage up
PVCC
+ 12 V
to the user designated level.
POR
CIRCUIT
ENABLE
COMPARATOR
+
-
EN
10.7k Ω
1.40k Ω
Intel Soft-Start
The soft-start function allows the converter to bring up the
output voltage in a controlled fashion, resulting in a linear
ramp-up. The soft-start sequence for the Intel modes of
operation is slightly different than the AMD soft-start
sequence.
0.85V
SOFT-START
AND
FAULT LOGIC
FIGURE 10. POWER SEQUENCING USING
V OUT , 500mV/DIV
THRESHOLD-SENSITIVE ENABLE (EN)
FUNCTION
t d1
t d2
t d3
t d4
t d5
Enable and Disable
While in shutdown mode, the LGATE and UGATE signals
are held low to assure the MOSFETs remain off. The
following input conditions must be met, for both Intel and
AMD modes of operation, before the ISL6314 is released
from shutdown mode to begin the soft-start start-up
sequence:
1. The bias voltage applied at VCC must reach the internal
power-on reset (POR) rising threshold. Once this
threshold is reached, proper operation of all aspects of
the ISL6314 is guaranteed. Hysteresis between the rising
and falling thresholds assure that once enabled, the
ISL6314 will not inadvertently turn off unless the bias
voltage drops substantially (see “Electrical
Specifications” on page 6).
2. The voltage on EN must be above 0.85V. The EN input
allows for power sequencing between the controller bias
voltage and another voltage rail. The enable comparator
holds the ISL6314 in shutdown until the voltage at EN
rises above 0.85V. The enable comparator has 110mV of
hysteresis to prevent bounce.
3. The driver bias voltage applied at the PVCC pin must
reach the internal power-on reset (POR) rising threshold.
Hysteresis between the rising and falling thresholds
assure that once enabled, the ISL6314 will not
EN
PGOOD
500μs/DIV
FIGURE 11. INTEL SOFT-START WAVEFORMS
For the Intel VR11 mode of operation, the soft-start
sequence is composed of four periods, as shown in
Figure 11. Once the ISL6314 is released from shutdown and
page 20), the controller will have fixed delay period t d1 ,
typically 1.1ms. After this delay period, the VR will begin first
soft-start ramp until the output voltage reaches 1.1V VBOOT
voltage. Then, the controller will regulate the VR voltage at
1.1V for another fixed period t d3, typically 93μs. At the end of
t d3 period, ISL6314 will read the VID signals. It is
recommended that the VID codes be set no later then 50μs
into period t d3 . If the VID code is valid, ISL6314 will initiate
the second soft-start ramp until the output voltage reaches
the VID voltage plus/minus any offset or droop voltage.
The soft-start time is the sum of the 4 periods as shown in
Equation 15.
inadvertently turn off unless the PVCC bias voltage drops
substantially (see “Electrical Specifications” on page 6).
t SS = t d1 + t d2 + t d3 + t d4
(EQ. 15)
For Intel VR11 and AMD 6-bit modes of operation these are
the only conditions that must be met for the controller to
immediately begin the soft-start sequence, as shown in
Figure 10. If running in AMD 5-bit mode of operation there is
one more condition that must be met:
20
During t d2 and t d4 , ISL6314 digitally controls the DAC
voltage change at 6.25mV per step. The time for each step is
determined by the frequency of the soft-start oscillator which
is defined by the resistor R SS from SS pin to GND. The
second soft-start ramp time t d2 and t d4 can be calculated
based on Equations 16 and 17:
FN6455.2
October 8, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| ESM24DRYI-S13 | CONN EDGECARD 48POS .156 EXTEND |
| 1944-06M | COIL RF .27UH MOLDED UNSHIELDED |
| ISL95870HRUZ-T | IC CTRLR PWM 1PHASE GPU 16UTQFN |
| MIC5301-2.85YML TR | IC REG LDO 2.85V .15A 6-MLF |
| ISL95870AHRUZ-T | IC CTRLR PWM 1PHASE GPU 20UTQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6315CRZ | 功能描述:IC REG CTRLR BUCK PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6315CRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6315CRZ-TK | 功能描述:IC REG CTRLR BUCK PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6315IRZ | 功能描述:IC REG CTRLR BUCK PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6315IRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。