参数资料
| 型号： | ISL6324CRZ-T |
| 厂商： | Intersil |
| 文件页数： | 10/38页 |
| 文件大小： | 0K |
| 描述： | IC HYBRID CTRLR PWM DUAL 48-QFN |
| 标准包装： | 4,000 |
| 应用： | 控制器，AMD SVI |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 2 |
| 输出电压： | 最高 2V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
ISL6324
FS
A resistor, placed from FS to Ground or from FS to VCC,
sets the switching frequency of both controllers. Refer to
Equation 1 for proper resistor calculation.
LGATE1 and LGATE2
These pins are used to control the lower MOSFETs. Connect
these pins to the corresponding lower MOSFETs’ gates.
PWM3 and PWM4
[ 10.61 – 1.035 log ( f ) ]
R T = 10
s
(EQ. 1)
Pulse-width modulation outputs. Connect these pins to the
PWM input pins of an Intersil driver IC if 3- or 4-phase
With the resistor tied from FS to Ground, Droop is enabled.
With the resistor tied from FS to VCC, Droop is disabled.
VSEN and RGND
VSEN and RGND are inputs to the core voltage regulator
(VR) controller precision differential remote-sense amplifier
and should be connected to the sense pins of the remote
processor core(s), VDDFB[H,L].
FB and COMP
These pins are the internal error amplifier inverting input and
output respectively of the core VR controller. FB, VSEN and
COMP are tied together through external R-C networks to
compensate the regulator.
APA
Adaptive Phase Alignment (APA) pin for setting trip level and
adjusting time constant. A 100μA current flows into the APA
pin and by tying a resistor from this pin to COMP the trip
level for the Adaptive Phase Alignment circuitry can be set.
ISEN1-, ISEN1+, ISEN2-, ISEN2+, ISEN3-, ISEN3+,
ISEN4-, and ISEN4+
These pins are used for differentially sensing the corresponding
channel output currents. The sensed currents are used for
channel balancing, protection, and core load line regulation.
Connect ISEN1-, ISEN2-, ISEN3-, and ISEN4- to the node
between the RC sense elements surrounding the inductor of
their respective channel. Tie the ISEN+ pins to the VCORE
side of their corresponding channel’s sense capacitor.
UGATE1 and UGATE2
Connect these pins to the corresponding upper MOSFET
gates. These pins are used to control the upper MOSFETs
and are monitored for shoot-through prevention purposes.
Maximum individual channel duty cycle is limited to 93.3%.
BOOT1 and BOOT2
These pins provide the bias voltage for the corresponding
upper MOSFET drives. Connect these pins to appropriately
chosen external bootstrap capacitors. Internal bootstrap
diodes connected to the PVCC1_2 pin provide the
necessary bootstrap charge.
PHASE1 and PHASE2
Connect these pins to the sources of the corresponding
upper MOSFETs. These pins are the return path for the
upper MOSFET drives.
10
operation is desired. Connect the ISEN- pins of the channels
not desired to +5V to disable them and configure the core
VR controller for 2-phase or 3-phase operation.
PWROK
System wide Power Good signal. If this pin is low, the two
SVI bits are decoded to determine the “metal VID”. When the
pin is high, the SVI is actively running its protocol.
RSET
Connect this pin to the VCC pin through a resistor (R SET ) to
set the effective value of the internal R ISEN current sense
resistors. The values of the R SET resistor should be no less
than 20k Ω and no more than 80k Ω . A 0.1μF capacitor
should be placed in parallel to the R SET resistor.
VDDPWRGD
During normal operation this pin indicates whether both output
voltages are within specified overvoltage and undervoltage
limits. If either output voltage exceeds these limits or a reset
event occurs (such as an overcurrent event), the pin is pulled
low. This pin is always low prior to the end of soft-start.
DVC
The DVC pin is a buffered version of the reference to the error
amplifier. A series resistor and capacitor between the DVC pin
and FB pin smooth the voltage transition during VID-on-the-fly
operations.
FB_NB and COMP_NB
These pins are the internal error amplifier inverting input and
output respectively of the NB VR controller. FB_NB,
VDIFF_NB, and COMP_NB are tied together through
external R-C networks to compensate the regulator.
ISEN_NB-, ISEN_NB+
These pins are used for differentially sensing the North
Bridge output current. The sensed current is used for
protection and load line regulation if droop is enabled.
Connect ISEN_NB- to the node between the RC sense
element surrounding the inductor. Tie the ISEN_NB+ pin to
the VNB side of the sense capacitor.
UGATE_NB
Connect this pin to the corresponding upper MOSFET gate.
This pin provides the PWM-controlled gate drive for the
upper MOSFET and is monitored for shoot-through
prevention purposes.
FN6518.2
September 25, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| LT1963AEFE-3.3#PBF | IC REG LDO 3.3V 1.5A 16TSSOP |
| HIP6004DCRZ-T | IC CTRLR PWM VOLTAGE MON 20-QFN |
| LT1963AEFE-1.8#PBF | IC REG LDO 1.8V 1.5A 16TSSOP |
| HIP6004BCRZ-T | IC CTRLR PWM VOLTAGE MON 20-QFN |
| ADP1710AUJZ-3.0-R7 | IC REG LDO 3V .15A TSOT-23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6324IRZ | 功能描述:IC HYBRID CTRLR PWM DUAL 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6324IRZ-T | 功能描述:IC HYBRID CTRLR PWM DUAL 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6326AIRZ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL6326BCRZ | 功能描述:电流型 PWM 控制器 W/ANNEAL 4-PHS VR11 CNTRLR COM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6326BCRZ-T | 功能描述:电流型 PWM 控制器 W/ANNEAL 4-PHS VR11 CNTRLR COM RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。