参数资料
| 型号： | ISL6336BCRZ |
| 厂商： | Intersil |
| 文件页数： | 11/31页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM SYNC BUCK 48-QFN |
| 标准包装： | 43 |
| 应用： | 控制器，Intel VR11.1 |
| 输入电压： | 3 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.5 V ~ 1.6 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（7x7） |
| 包装： | 管件 |
| 产品目录页面： | 1248 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
ISL6336B
OFS - The OFS pin provides a means to program a DC
offset current for generating a DC offset voltage at the REF
input. The offset current is generated via an external resistor
and precision internal voltage references. The polarity of the
offset is selected by connecting the resistor to GND or VCC.
For no offset, the OFS pin should be left unterminated.
TCOMP - Temperature compensation scaling input. The
voltage sensed on the TM pin is utilized as the temperature
input to adjust I DROOP and the overcurrent protection limit to
effectively compensate for the temperature coefficient of the
current sense element. To implement the integrated
temperature compensation, a resistor divider circuit is needed
with one resistor being connected from TCOMP to VCC of the
controller and another resistor being connected from TCOMP
to GND. Changing the ratio of the resistor values will set the
gain of the integrated thermal compensation. When integrated
temperature compensation function is not used, connect
TCOMP to GND.
OVP - The overvoltage protection output indication pin. This
pin can be pulled to VCC and is latched when an overvoltage
condition is detected. When the OVP indication is not used,
keep this pin open.
IMON - IMON is a current output of the average of the sum
of each phase’s sensed current. A resistor connected from
IMON to GND will produce a voltage that is proportional to
the regulator current. The voltage at this pin is internally
clamped to 1.12V. If the voltage reaches 1.12V the clamp is
activated an overcurrent shutdown will be initiated.
Place a resistor from this pin to GND. A capacitor in parallel
with this resistor is required. The capacitor should be sized
for a minimum time constant of 300μs.
TM - TM is an input pin for VR temperature measurement.
Connect this pin through NTC thermistor to GND and a resistor
to VCC of the controller. The voltage at this pin is reverse
proportional to the VR temperature. ISL6336B monitors the VR
temperature based on the voltage at the TM pin and the output
signal at VR_HOT.
VR_HOT - VR_HOT is used as an indication of high VR
temperature. It is an open-drain logic output. It will be open
when the measured VR temperature reaches a certain level.
PSI# - The PSI# pin is used to change the state of the
controller. When PSI# is asserted the controller will change
the operating state to improve light load efficiency. The
controller drops the number of active phases to 1-phase or
2-phase operation with diode emulation according to the logic
shown in Table 1. The FS and SS pins are used to optimize
light load efficiency for non-coupled inductor, 2-phase coupled
inductor, and (n-x)-phase coupled inductor applications. The
controller resumes normal operation when this pin is pulled
HIGH. This pin has a 40μA internal pull-up to about 1V.
11
H_CPURST_N - This pin determines whether the PSI# input
is recognized and the IC enters the low-power, phase
dropping state. While in a logic LOW state and for 45ms
(typically) after returning HIGH, the controller will be
prevented from entering low power mode of operation by
locking out the PSI# input. Left open at start-up, this pin is
pulled to about 1.2V by an internal current source, and the
PSI# input is locked out for 45ms. To disable this functionality
APA - The APA pin is used to adjust the Adaptive Phase
Alignment trip level. A 50μA current source flows into this pin.
A resistor connected from this pin to COMP sets the voltage
trip level. A small decoupling capacitor should be placed in
parallel with the resistor for high frequency decoupling.
Operation
Multiphase Power Conversion
Microprocessor load current profiles have changed to the
point that the advantages of multiphase power conversion
are impossible to ignore. The technical challenges
associated with producing a single-phase converter which is
both cost-effective and thermally viable, have forced a
change to the cost-saving approach of multiphase. The
ISL6336B controller helps reduce the complexity of
implementation by integrating vital functions and requiring
and 6 provide top level views of multiphase power
conversion using the ISL6336B controller.
Interleaving
The switching of each channel in a multiphase converter is
timed to be symmetrically out of phase with each of the other
channels. In a 3-phase converter for example, each channel
switches 1/3 cycle after the previous channel and 1/3 cycle
before the following channel. As a result, the three-phase
converter has a combined ripple frequency three times
greater than the ripple frequency of any one phase. In
addition, the peak-to-peak amplitude of the combined
inductor current is reduced in proportion to the number of
phases (see Equations 1 and 2). The increased ripple
frequency and the lower ripple amplitude mean that the
designer can use less per-channel inductance and lower
total output capacitance for any performance specification.
Figure 1 illustrates the multiplicative effect on output ripple
frequency. The three channel currents (IL1, IL2, and IL3)
combine to form the AC ripple current and the DC load
current. The ripple component has three times the ripple
frequency of each individual channel current. Each PWM
pulse is triggered 1/3 of a cycle after the start of the PWM
pulse of the previous phase. The DC components of the
inductor currents combine to feed the load.
FN6696.2
August 31, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6336IRZ | IC CTRLR PWM 6PHASE BUCK 48-QFN |
| ISL6341CIRZ | IC REG CTRLR BUCK PWM VM 10-TDFN |
| ISL6353IRTZ | IC CONTROLLER DDR VR12 40TQFN |
| ISL6363IRTZ-T | IC CONTROLLER VR12 48TQFN |
| ISL6401CR-T | IC REG CTRLR BST FLYBK ISO 16QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6336BCRZ-T | 功能描述:IC CTRLR PWM SYNC BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6336BIRZ | 功能描述:IC CTRLR PWM SYNC BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6336BIRZ-T | 功能描述:IC CTRLR PWM SYNC BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6336CRZ | 功能描述:IC CTRLR PWM 6PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6336CRZ-T | 功能描述:IC CTRLR PWM 6PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。