参数资料
| 型号： | ISL6423ERZ-T |
| 厂商： | Intersil |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC VREG SGL LNB W/I2C 24-QFN |
| 标准包装： | 6,000 |
| 应用： | 转换器，卫星信号接收机顶盒设计 |
| 输入电压： | 8 V ~ 14 V |
| 输出数： | 1 |
| 输出电压： | 13.3 V ~ 18.3 V，14.3 V ~ 19.3 V |
| 工作温度： | -20°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
| 包装： | 带卷 (TR) |
ISL6423
However, there could be some cases in which a highly
capacitive load on the output may cause a difficult start-up
when the dynamic protection is selected. This can be solved
by initiating any power start-up in static mode (DCL = HIGH)
and then switching to the dynamic mode (DCL = LOW) after
a predetermined interval. When in static mode, the OLF bit
goes HIGH when the current clamp limit is reached and
returns LOW when the overload condition is cleared. The
OLF/BCF bit will be LOW at the end of initial power-on soft-
start. In the static mode the output current through the linears
is limited to a 990mA typical.
When a 19.3V line is connected onto a VOUT1 or 2 that has
been set to 13.3V the linear will then enter a back current
limited state. When a back current of greater than 125mA
typical is sensed at the lower FET of the linear for a period
greater that 100μs, the output is disabled for a period of 5ms
and the BCF bit is set. If the 19.3V remains connected, the
output will cycle through the ON = 100μs/OFF = 5ms. The
output will recover when the fault is removed.
Thermal Protection
This IC is protected against overheating. When the junction
temperature exceeds 150°C (typical), the step-up converter
and the linear regulator are shut off and the OTF bit of the
SR is set HIGH. When the junction is cooled down to +130°C
(typical), normal operation is resumed and the OTF bit is
reset LOW.
In over temperature conditions, the OTF flag goes HIGH and
the I 2 C data will be cleared. The user may need to monitor
the I 2 C enable bits and OTF flag continuously and enable
the chip, if I 2 C data is cleared. OTF conditions may also
make the OLF flags go HIGH, when high capacitive loads
are present or self-heating conditions occur at higher loads.
External Output Voltage Selection
When the I 2 C bit VSPEN is set high the output voltage can
be selected by the I 2 C bus. Additionally, the package offers
the pin SELVTOP for independent 13V thru 19V output
voltage selection, when the VSPEN bit is set low. A
summary of the voltage control is given in the Table 1. For
further details refer to the individual registers SR1 and SR3
TABLE 1.
I 2 C Bus Interface for ISL6423
(Refer to Philips I 2 C Specification, Rev. 2.1)
Data transmission from main microprocessor to the ISL6423
and vice versa takes place through the two wire I 2 C bus
interface, consisting of the two lines SDA and SCL. Both
SDA and SCL are bidirectional lines, connected to a positive
supply voltage via a pull up resistor. (Pull-up resistors to
positive supply voltage must be externally connected). When
the bus is free, both lines are HIGH. The output stages of
ISL6423 will have an open drain/open collector in order to
perform the wired-AND function. Data on the I 2 C bus can be
transferred up to 100kbps in the standard-mode or up to
400kbps in the fast-mode. The level of logic “0” and logic “1”
is dependent of associated value of V DD as per electrical
specification table. One clock pulse is generated for each
data bit transferred.
Data Validity
The data on the SDA line must be stable during the HIGH
period of the clock. The HIGH or LOW state of the data line
can only change when the clock signal on the SCL line is
LOW. Refer to Figure 4.
SDA
SCL
DATA LINE CHANGE
STABLE OF DATA
DATA VALID ALLOWED
FIGURE 4. DATA VALIDITY
START and STOP Conditions
As shown in Figure 5, START condition is a HIGH to LOW
transition of the SDA line while SCL is HIGH.
The STOP condition is a LOW to HIGH transition on the SDA
line while SCL is HIGH. A STOP condition must be sent
before each START condition.
VSPEN
0
0
VTOP
x
x
VBOT
0
1
SELVTOP
0
0
VOUT (V)
13.3
14.3
SDA
SCL
0
0
1
0
1
0
x
x
0
1
1
x
18.3
19.3
13.3
S
START
CONDITION
P
STOP
CONDITION
1
1
1
0
1
1
1
0
1
x
x
x
14.3
18.3
19.3
FIGURE 5. START AND STOP WAVEFORMS
10
FN9191.2
December 5, 2008
相关PDF资料 |
PDF描述 |
|---|---|
| LT1963AEQ#PBF | IC REG LDO ADJ 1.5A 5-DD |
| URZ2A220MPD | CAP ALUM 22UF 100V 20% RADIAL |
| GMA30DRMI-S288 | CONN EDGECARD 60POS .125 EXTEND |
| ISL95870BHRZ | IC CTRLR PWM 1PHASE GPU 20QFN |
| MIC5320-NNYMT TR | IC REG LDO 2.85V .15A 6-TMLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6423EVEZ | 功能描述:电流型 PWM 控制器 NOTCOMENDED FOR NEW DESIGN RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6423EVEZ-T | 功能描述:电流型 PWM 控制器 NOTCOMENDED FOR NEW DESIGN RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6424ER | 功能描述:IC REG DUAL LNBP TTL-INP 32-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6424ER-T | 功能描述:IC REG DUAL LNBP TTL-INP 32-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6424ERZ | 功能描述:直流/直流开关调节器 DL LNBP SUPP CONTROL VG W/TTL INPUTS 3 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。