参数资料
| 型号： | ISL6564IR-T |
| 厂商： | Intersil |
| 文件页数： | 14/27页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 40-QFN |
| 标准包装： | 4,000 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1.5MHz |
| 占空比： | 66.7% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
ISL6564
L
ISL6564 INTERNAL CIRCUIT
L
I
R SENSE V OUT
C OUT
Channel-Current Balance
The sampled currents I n , from each active channel are
summed together and divided by the number of active
channels. The resulting cycle average current I AVG , provides
a measure of the total load current demand on the converter
I n
SAMPLE
&
HOLD
ISEN-(n)
R ISEN(n)
during each switching cycle. Channel current balance is
achieved by comparing the sampled current of each channel
to the cycle average current, and making an appropriate
adjustment to each channel pulse width based on the error.
Intersil’s patented current-balance method is illustrated in
+
-
ISEN+(n)
I R SENSE
R
SEN = I L --------------------------
ISEN
FIGURE 5. SENSE RESISTOR IN SERIES WITH INDUCTORS
MOSFET r DS(ON) SENSING
Figure 7, with error correction for channel 1 represented. In
the figure, the cycle average current combines with the
channel 1 sample, I 1 , to create an error signal I ER . The
filtered error signal modifies the pulse width commanded by
V COMP to correct any unbalance and force I ER toward zero.
The same method for error signal correction is applied to
each active channel.
The controller can also sense the channel load current by
sampling the voltage across the lower MOSFET r DS(ON)
(see Figure 6). The amplifier is ground-reference by
V COMP
+
-
+
-
PWM1
f(j ω )
FILTER
Σ
connecting the ISEN- input to the source of the lower
MOSFET. ISEN+ connects to the PHASE node through a
resistor R ISEN . The voltage across R ISEN is equivalent to
the voltage drop across the r DS(ON) of the lower MOSFET
while it is conducting. The resulting current into the ISEN+
pin is proportional to the channel current I L . The ISEN
current is then sampled and held after sufficient settling time.
The sampled current I n , is used for channel-current balance,
load-line regulation, and overcurrent protection. From
SAWTOOTH SIGNAL
I ER
I AVG
÷ N
-
+
I 1
NOTE: *Channels 3 and 4 are optional.
I 4 *
I 3 *
I 2
Figure 6, Equation 7 for I SEN is derived.
FIGURE 7. CHANNEL-1 PWM FUNCTION AND CURRENT-
I SEN = I ------------------------- ) -
DS ( ON
L R
I n
r
ISEN
V IN
BALANCE ADJUSTMENT
Channel current balance is essential in realizing the thermal
advantage of multi-phase operation. The heat generated in
SAMPLE
&
HOLD
ISEN+(n)
I L
down converting is dissipated over multiple devices and a
greater area. The designer avoids the complexity of driving
multiple parallel MOSFETs, and the expense of using heat
L DS ( ON )
-
R ISEN
(PTC)
ISEN-(n)
-
I
+
r
sinks and nonstandard magnetic materials.
Voltage Regulation
+
N-CHANNEL
MOSFETs
The integrating compensation network shown in Figure 8
assures that the steady-state error in the output voltage is
limited only to the error in the reference voltage (output of
ISL6564 INTERNAL CIRCUIT
EXTERNAL CIRCUIT
the DAC) and offset errors in the OFS current source,
remote-sense and error amplifiers. Intersil specifies the
FIGURE 6. MOSFET r DS(ON) CURRENT-SENSING CIRCUIT
guaranteed tolerance of the ISL6564 to include the
combined tolerances of each of these elements.
I SEN = I L ---------------------- )
r DS ( ON
R ISEN
(EQ. 7)
The output of the error amplifier, V COMP , is compared to the
sawtooth waveform to generate the PWM signals. The PWM
where I L is the channel current. Since MOSFET r DS(ON)
increases with temperature, a PTC resistor should be
chosen for R ISEN to compensate for this change.
14
signals control the timing of the Intersil MOSFET drivers and
regulate the converter output to the specified reference
voltage. The internal and external circuitry which control
voltage regulation is illustrated in Figure 8.
FN9156.2
December 27, 2004
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6565BCV-T | IC REG CTRLR BUCK PWM VM 28TSSOP |
| ISL6566AIRZ | IC CTRLR PWM 3PHASE BUCK 40-QFN |
| ISL6566CRZ-T | IC CTLR PWM BUCK 3PHASE 40-QFN |
| ISL6567CRZ | IC REG CTRLR BUCK PWM VM 24-QFN |
| ISL6568CRZ-T | IC CTLR PWM BUCK 2PHASE 32-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6564IRZ | 功能描述:电流型 PWM 控制器 MULTI-PHS PWM CNTRLR W/0 525-1 3 VID INDU RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6564IRZ-T | 功能描述:电流型 PWM 控制器 MULTI-PHS PWM CNTRLR W/0 525-1 3 VID RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6565ACB | 功能描述:IC REG CTRLR BUCK PWM VM 28-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
| ISL6565ACB-T | 功能描述:IC REG CTRLR BUCK PWM VM 28-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:100% 电源电压:8.2 V ~ 30 V 降压:无 升压:无 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:0°C ~ 70°C 封装/外壳:8-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:1316 (CN2011-ZH PDF) |
| ISL6565ACBZ | 功能描述:IC REG CTRLR BUCK PWM VM 28-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。