参数资料
| 型号： | ISL6566ACRZ |
| 厂商： | Intersil |
| 文件页数： | 10/28页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM 3PHASE BUCK 40-QFN |
| 标准包装： | 500 |
| 应用： | 控制器，Intel VRM9，VRM10，AMD Hammer 应用 |
| 输入电压： | 3 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.8 V ~ 1.6 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | * |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 供应商设备封装： | * |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
ISL6566A
V COMP voltage crosses the sawtooth ramp, the PWM output
transitions high. The internal or external MOSFET driver
detects the change in state of the PWM signal and turns off
the synchronous MOSFET and turns on the upper MOSFET.
The PWM signal will remain high until the pulse termination
signal marks the beginning of the next cycle by triggering the
PWM signal low.
Channel-Current Balance
One important benefit of multi-phase operation is the thermal
advantage gained by distributing the dissipated heat over
multiple devices and greater area. By doing this the designer
avoids the complexity of driving parallel MOSFETs and the
expense of using expensive heat sinks and exotic magnetic
materials.
In order to realize the thermal advantage, it is important that
each channel in a multi-phase converter be controlled to
carry about the same amount of current at any load level. To
achieve this, the currents through each channel must be
sampled every switching cycle. The sampled currents, I n ,
from each active channel are summed together and divided
Current Sampling
In order to realize proper current-balance, the currents in
each channel must be sampled every switching cycle. This
sampling occurs during the forced off-time, following a PWM
transition low. During this time the current-sense amplifier
uses the ISEN inputs to reproduce a signal proportional to
the inductor current, I L . This sensed current, I SEN , is simply
a scaled version of the inductor current. The sample window
opens exactly 1/6 of the switching period, t SW , after the
PWM transitions low. The sample window then stays open
the rest of the switching cycle until PWM transitions high
again, as illustrated in Figure 4.
The sampled current, at the end of the t SAMPLE , is
proportional to the inductor current and is held until the next
switching period sample. The sampled current is used only
for channel-current balance.
I L
by the number of active channels. The resulting cycle
average current, I AVG , provides a measure of the total load-
current demand on the converter during each switching
cycle. Channel-current balance is achieved by comparing
the sampled current of each channel to the cycle average
current, and making the proper adjustment to each channel
pulse width based on the error. Intersil’s patented current-
balance method is illustrated in Figure 3, with error
correction for channel 1 represented. In the figure, the cycle
PWM
SWITCHING PERIOD
I SEN
SAMPLING PERIOD
average current, I AVG , is compared with the channel 1
sample, I 1 , to create an error signal I ER .
The filtered error signal modifies the pulse width
commanded by V COMP to correct any unbalance and force
I ER toward zero. The same method for error signal
correction is applied to each active channel.
OLD SAMPLE NEW SAMPLE
CURRENT CURRENT
TIME
FIGURE 4. SAMPLE AND HOLD TIMING
The ISL6566A supports MOSFET r DS(ON) current sensing
to sample each channel’s current for channel-current
V COMP
+
-
+
-
PWM1
TO GATE
CONTROL
LOGIC
balance. The internal circuitry, shown in Figure 5 represents
channel n of an N-channel converter. This circuitry is
repeated for each channel in the converter, but may not be
FILTER
f(s)
SAWTOOTH SIGNAL
active depending on the status of the PVCC3 and PVCC2
pins, as described in the PWM Operation section.
I ER
+
-
I AVG
÷ N
Σ
I 3
I 2
I 1
NOTE: Channel 2 and 3 are optional.
FIGURE 3. CHANNEL-1 PWM FUNCTION AND CURRENT-
BALANCE ADJUSTMENT
10
FN9200.2
July 27, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| ACM25DSES-S243 | CONN EDGECARD 50POS .156 EYELET |
| 2510-28K | INDUCTOR RF 1.5UH UNSHIELDED SMD |
| LT1175IS8-5#PBF | IC REG LDO -5V .5A 8SOIC |
| LT1175IS8#PBF | IC REG LDO NEG ADJ .5A 8SOIC |
| ABM25DSES-S243 | CONN EDGECARD 50POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6566ACRZ-T | 功能描述:IC CTRLR PWM 3PHASE BUCK 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6566AIRZ | 功能描述:IC CTRLR PWM 3PHASE BUCK 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6566AIRZ-T | 功能描述:IC CTRLR PWM 3PHASE BUCK 40-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6566CR | 功能描述:IC CTRLR PWM BUCK 3PHASE 40-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6566CRR5184 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。