- 您现在的位置：买卖IC网 > PDF目录15216 > ISL8105AIRZ-T (Intersil)IC REG CTRLR BUCK PWM VM 10-DFN PDF资料下载
参数资料
| 型号： | ISL8105AIRZ-T |
| 厂商： | Intersil |
| 文件页数： | 6/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 10-DFN |
| 标准包装： | 6,000 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 660kHz |
| 占空比： | 100% |
| 电源电压： | 6.5 V ~ 14.4 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
ISL8105, ISL8105A
LX (SOIC Pin 8, DFN Pin 10)
Connect this pin to the source of the top-side MOSFET and
the drain of the bottom-side MOSFET. It is used as the sink
for the TGATE driver and to monitor the voltage drop across
the bottom-side MOSFET for overcurrent protection. This pin
is also monitored by the adaptive shoot-through protection
circuitry to determine when the top-side MOSFET has turned
off.
N/C (DFN Only; Pin3, Pin 7)
These two pins in the DFN package are No Connect.
Functional Description
Initialization (POR and OCP Sampling)
Figure 1 shows a start-up waveform of ISL8105. The
Power-ON-Reset (POR) function continually monitors the
bias voltage at the VBIAS pin. Once the rising POR
threshold is exceeded 4V (V POR nominal), the POR function
initiates the Overcurrent Protection (OCP) sample and hold
operation (while COMP/EN is ~1V). When the sampling is
complete, V OUT begins the soft-start ramp.
time, the BGATE/BSOC pin is initialized by disabling the
BGATE driver and drawing BSOC (nominal 21.5μA) through
R BSOC . This sets up a voltage that will represent the BSOC
trip point. At t 2 , there is a variable time period for the OCP
sample and hold operation (0ms to 3.4ms nominal; the
longer time occurs with the higher overcurrent setting). The
sample and hold uses a digital counter and DAC to save the
voltage, so the stored value does not degrade, for as long as
the V BIAS is above V POR . See “Overcurrent Protection
(OCP)” on page 7 for more details on the equations and
variables. Upon the completion of sample and hold at t 3 , the
soft-start operation is initiated, and the output voltage ramps
up between t 4 and t 5 .
BGATE
STARTS
SWITCHING
COMP/EN
V OUT
BGATE/BSOC
V BIAS
3.4ms
3.4ms
0ms to 3.4ms
~4V POR
V OUT
t0 t1
t2 t3 t4
t5
V COMP/EN
FIGURE 1. POR AND SOFT-START OPERATION
If the COMP/EN pin is held low during power-up, the
initialization will be delayed until the COMP/EN is released
and its voltage rises above the V DISABLE trip point.
Figure 2 shows a typical power-up sequence in more detail.
The initialization starts at t 0 , when either V BIAS rises above
V POR , or the COMP/EN pin is released (after POR). The
COMP/EN will be pulled up by an internal 20μA current
source, but the timing will not begin until the COMP/EN
exceeds the V DISABLE trip point (at t 1 ). The external
capacitance of the disabling device, as well as the
compensation capacitors, will determine how quickly the
20μA current source will charge the COMP/EN pin. With
typical values, it should add a small delay compared to the
soft-start times. The COMP/EN will continue to ramp to ~1V.
From t 1 , there is a nominal 6.8ms delay, which allows the
VBIAS pin to exceed 6.5V (if rising up towards 12V), so that
the internal bias regulator can turn on cleanly. At the same
6
FIGURE 2. BGATE/BSOC AND SOFT-START OPERATION
Soft-Start and Pre-Biased Outputs
Functionally, the soft-start internally ramps the reference on
the non-inverting terminal of the error amp from 0V to 0.6V in
a nominal 6.8ms. The output voltage will thus follow the
ramp, from zero to final value, in the same 6.8ms (the actual
ramp seen on the V OUT will be less than the nominal time),
due to some initialization timing, between t 3 and t 4 ).
The ramp is created digitally, so there will be 64 small
discrete steps. There is no simple way to change this ramp
rate externally, and it is the same for either frequency
version of the IC (300kHz or 600kHz).
After an initialization period (t 3 to t 4 ), the error amplifier
(COMP/EN pin) is enabled, and begins to regulate the
converter's output voltage during soft-start. The oscillator's
triangular waveform is compared to the ramping error
amplifier voltage. This generates LX pulses of increasing
width that charge the output capacitors. When the internally
generated soft-start voltage exceeds the reference voltage
(0.6V), the soft-start is complete and the output should be in
regulation at the expected voltage. This method provides a
rapid and controlled output voltage rise; there is no large
inrush current charging the output capacitors. The entire
start-up sequence from POR typically takes up to 17ms; up
FN6306.5
April 15, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| ISL8105BIRZ-T | IC REG CTRLR BUCK PWM VM 10-DFN |
| B41041A6108M | 1000UF 50V 16X25 SINGLE END |
| ISL8105IRZ-T | IC REG CTRLR BUCK PWM VM 10-DFN |
| MC33164DM-3R2G | IC SENSOR UNDERVOLTAGE 8-MICRO |
| RBM28DSXH | CONN EDGECARD 56POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8105B | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:+5V or +12V Single-Phase Synchronous Buck Converter PWM Controller with Integrated MOSFET Gate Drivers, Extended Soft-Start Time |
| ISL8105BCBZ | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL8105BCBZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| ISL8105BCRZ | 功能描述:IC REG CTRLR BUCK PWM VM 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL8105BCRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
发布紧急采购，3分钟左右您将得到回复。