- 您现在的位置：买卖IC网 > PDF目录15163 > ISL8126IRZ-TK (Intersil)IC REG CTRLR BUCK PWM VM 32-QFN PDF资料下载
参数资料
| 型号： | ISL8126IRZ-TK |
| 厂商： | Intersil |
| 文件页数： | 3/39页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 32-QFN |
| 标准包装： | 1,000 |
| PWM 型： | 电压模式 |
| 输出数： | 2 |
| 频率 - 最大： | 1.5MHz |
| 占空比： | 90% |
| 电源电压： | 3 V ~ 5.6 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
ISL8126
Functional Pin Descriptions (Continued)
PIN
NUMBER
4, 6
5
7
8
32, 10
31, 11
30, 12
SYMBOL
EN/VFF1, EN/VFF2
FSYNC
CLKOUT/REFIN
PGOOD
FB1, FB2
VMON1, VMON2
VSEN1-, VSEN2-
3
DESCRIPTION
These pins have triple functions. The voltage on EN/VFF_ pin is compared with a precision 0.8V threshold
for system enable to initiate soft-start. With a voltage lower than the threshold, the corresponding channel
can be disabled independently. By connecting these pins to the input rail through a voltage resistor divider,
the input voltage can be monitored for UVLO (undervoltage lockout) function. The undervoltage lockout and
its hysteresis levels can be programmed by these resistor dividers. The voltages on these pins are also fed
into the controller to adjust the sawtooth amplitude of each channel independently to realize the feed-
forward function.
Furthermore, during fault (such as overvoltage, overcurrent, and over-temperature) conditions, these pins
(EN/VFF_) are pulled low to communicate the information to other cascaded ICs.
The oscillator switching frequency is adjusted by placing a resistor (RFS) from this pin to GND. The internal
oscillator will lock to an external frequency source if this pin is connected to a switching square pulse
waveform, typically the CLKOUT signal from another ISL8126 or an external clock. The internal oscillator
synchronizes with the leading edge of the input signal.
This pin has a dual function depending on the mode in which the chip is operating. It provides a clock signal
to synchronize with other ISL8126(s) with its VSEN2- pulled within 400mV of VCC for multiphase (3-, 4-, 6-,
8-, 10-, or 12-phase) operation. When the VSEN2- pin is not within 400mV of VCC, ISL8126 is in dual mode
(dual independent PWM output). The clockout signal of this pin is not available in this mode, but the
ISL8126 can be synchronized to external clock. In dual mode, this pin works as the following two functions:
1. An external reference (0.6V target only) can be in place of the Channel 2’s internal reference through
this pin for DDR/tracking applications.
2. The ISL8126 operates as a dual-PWM controller for two independent regulators with selectable phase
Provides an open drain Power-Good signal when both channels are within 9% of the nominal output
regulation point with 4% hysteresis (13%/9%) and soft-start complete. PGOOD monitors the outputs
(VMON1/2) of the internal differential amplifiers.
These pins are the inverting inputs of the error amplifiers. These pins should be connected to VMON1,
VMON2 with the compensation feedback network. No direct connection between FB and VMON pins is
allowed. With VSEN2- pulled within 400mV of VCC, the corresponding error amplifier is disabled and the
amplifier’s output is high impedance. FB2 is one of the two pins to determine the relative phase
relationship between the internal clock of both channels and the CLKOUT signal. See Table 2 on page 23.
These pins are outputs of the differential amplifiers. They are connected internally to the OV/UV/PGOOD
comparators. These pins should be connected to the FB1, FB2 pins by a standard feedback network when
both channels are operating independently. When VSEN1-, VSEN2- are pulled within 400mV of VCC, the
corresponding differential amplifier is disabled and its output (VMON pin) is high impedance. In such an
event, the VMON pins can be used as additional monitors of the output voltage with a resistor divider to
protect the system against single point of failure, which occurs in the system using the same resistor
divider for both of the UV/OV comparator and output voltage feedback.
These pins are the negative inputs of standard unity gain operational amplifier for differential remote
sense for the corresponding regulator (Channels 1 and 2), and should be connected to the negative rail of
the load.
When VSEN1-, VSEN2- are pulled within 400mV of VCC, the corresponding error amplifier and differential
amplifier are disabled and their outputs are high impedance. Both VSEN2+ and FB2 input signal levels
determine the relative phases between the internal controllers as well as the CLKOUT signal. See Table 2
When configured as multiple power modules (each module with independent voltage loop) operating in
parallel, in order to implement the current sharing control, a resistor needs to be inserted between the
VSEN1- pin and the output voltage negative sense point (between VSEN1- and lower voltage sense resistor),
as shown in the “Typical Application Circuits” “ Multiple Power Modules in Parallel with Current Sharing
Control ” on page 14. This introduces a correction voltage for the modules with lower load current to keep
the current distribution balanced among modules. The module with the highest load current will
automatically become the master module. The recommended value for the VSEN1- resistor is 100 Ω and it
should not be large in order to keep the unit gain amplifier input impedance compatibility. A capacitor is
also recommended to place in parallel with the 100 Ω .
FN7892.1
August 16, 2012
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J5M-EY-F1 | CONVERTER MOD DC/DC 10V 50W |
| VE-2TV-EW-F3 | CONVERTER MOD DC/DC 5.8V 100W |
| ISL8126IRZ-T | IC REG CTRLR BUCK PWM VM 32-QFN |
| VE-2TV-EW-F2 | CONVERTER MOD DC/DC 5.8V 100W |
| VE-2TV-EW-F1 | CONVERTER MOD DC/DC 5.8V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8128IAZ-TK | 制造商:Intersil Corporation 功能描述:PB-FREE SYNC BUCK PWM CONT. W/ 4.5V-28V |
| ISL8130 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Advanced Single Universal Pulse-Width Modulation (PWM) Controller |
| ISL8130EVAL3Z | 制造商:Intersil Corporation 功能描述:ISL8130 EVALUATION BOARD 3 - 20LD QSOP - ROHS COMPLIANT - Bulk 制造商:Intersil Corporation 功能描述:BOARD EVAL FOR ISL8130 制造商:Intersil Corporation 功能描述:ISL8130 EVALUATION BOARD 3 - 20LD QSOP - RoHS COMPLIANT |
| ISL8130IAZ | 功能描述:IC REG CTRLR BST FLYBK VM 20QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL8130IAZ-T7A | 功能描述:电流型 PWM 控制器 PB-FREE SYNC BUCK PWM CONT. W/ 4.5V-28V INPUT,20LD QSOP, 250 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。