参数资料
| 型号： | ISL8500IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 11/15页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 2A 12DFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 6,000 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 19 V |
| 输入电压： | 4.5 V ~ 25 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-VFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 12-DFN（4x3） |
ISL8500
Output Voltage Selection
The regulator output voltages can be programmed using
external resistor dividers that scale the voltage feedback
relative to the internal reference voltage. The scaled voltage
is fed back to the inverting input of the error amplifier; refer to
Figure 20.
The output voltage programming resistor, R 4 , will depend on
the value chosen for the feedback resistor, R 1 , and the desired
output voltage, V OUT , of the regulator; see Equation 2. The
value for the feedback resistor is typically between 1k Ω and
10k Ω .
cycles, the overcurrent fault counter overflows, indicating an
overcurrent fault condition exists. The regulator is shut down
and power good goes low. If the overcurrent condition clears
prior to the counter reaching four consecutive cycles, the
internal flag and counter are reset.
The protection circuitry attempts to recover from the
overcurrent condition after waiting 4 soft-start cycles. The
internal overcurrent flag and counter are reset. A normal
soft-start cycle is attempted and normal operation continues
if the fault condition has cleared. If the overcurrent fault
counter overflows during soft-start, the converter shuts down
R 4 = ----------------------------------
R 1 × 0.6V
V OUT – 0.6V
(EQ. 2)
and this hiccup mode operation repeats.
There is 100ns blanking time for noise immunity. It is
If the output voltage desired is 0.6V, then R P is left
unpopulated.
R1
V OUT
recommended to operate the duty cycle higher than the
blanking time to insure proper overcurrent protection.
Undervoltage Protection
If the voltage detected on the buck regulator FB pin falls 25%
below the internal reference voltage, the undervoltage fault
EA
0.6V
REFERENCE
R4
condition flag is set. The regulator is shutdown. The
controller enters a recovery mode similar to the overcurrent
hiccup mode. No action is taken for 4 soft-start cycles and
the internal undervoltage counter and fault condition flag are
reset. A normal soft-start cycle is attempted and normal
FIGURE 20. EXTERNAL RESISTOR DIVIDER
The buck output can be programmed as high as 19V. Proper
heatsinking must be provided to insure that the junction
temperature does not exceed +125°C.
When the output is set greater than 2.7V, it is recommended to
pre-load at least 10mA and make sure that the input rise time is
>> faster than the VOUT1 rise time. This allows the BOOT
capacitor adequate time to charge for proper operation.
Protection Features
The ISL8500 limits current in the power devices to limit on-chip
power dissipation. Overcurrent limits on the regulator protect
the internal power device from excessive thermal damage.
Undervoltage protection circuitry on the buck regulator provides
a second layer of protection for the internal power device under
high current condition.
operation continues if the fault condition has cleared. If the
undervoltage counter overflows during soft-start, the
converter is shut down and this hiccup mode operation
repeats.
Thermal Overload Protection
Thermal overload protection limits total power dissipation in
the ISL8500. There is a sensor on the chip to monitor the
junction temperature of the internal LDO and PWM switching
power N-Channel MOSFET. When the junction temperature
(T J ) of the sensor exceeds +150°C, the thermal sensor
sends a signal to the fault monitor.
The fault monitor commands the buck regulator to shut down.
The buck regulator soft-starts turn on again after the IC’s
junction temperature cools by +20°C. The buck regulator
experiences hiccup mode operation during continuous thermal
overload conditions. For continuous operation, do not exceed
the +125°C junction temperature rating.
Buck Regulator Overcurrent Protection
During the PWM on-time, the current through the internal
switching MOSFET is sampled and scaled through an
internal pilot device. The sampled current is compared to a
nominal 3.5A overcurrent limit. If the sampled current
exceeds the overcurrent limit reference level, an internal
overcurrent fault counter is set to 1 and an internal flag is
set. The internal power MOSFET is immediately turned off
and will not be turned on again until the next switching cycle.
The protection circuitry continues to monitor the current and
turns off the internal MOSFET as described. If the
overcurrent condition persists for eight sequential clock
11
Application Guidelines
Operating Frequency
The ISL8500 operates at a fixed switching frequency of
500kHz.
Buck Regulator Output Capacitor Selection
An output capacitor is required to filter the inductor current
and supply the load transient current. The filtering
requirements are a function of the switching frequency and
the ripple current. The load transient requirements are a
function of the slew rate (di/dt) and the magnitude of the
FN6611.0
December 10, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| ISL8502AIRZ | IC REG BUCK SYNC ADJ 2A 24QFN |
| ISL8502IRZ | IC REG BUCK SYNC ADJ 2.5A 24QFN |
| ISL85033IRTZ | IC REG BUCK SYNC ADJ 3A 28TQFN |
| ISL85402IRZ | IC REG BUCK BOOST SYNC ADJ 20QFN |
| ISL8540IVEZ-T | IC REG BUCK SYNC ADJ 2A 20HTSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL8501EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL8501 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL8501IRZ | 功能描述:电压模式 PWM 控制器 INTEGRTD FETUCK 4X 4 24LD W/ANNEAL RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL8501IRZ-T | 功能描述:电压模式 PWM 控制器 INTEGRTD FETUCK 4X 4 24LD W/ANNEAL RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL8502AEVAL1Z | 功能描述:EVAL BOARD FOR ISL8502 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL8502AIRZ | 功能描述:IC REG BUCK SYNC ADJ 2A 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:1 输出电压:5V，1 V ~ 10 V 输入电压:3.5 V ~ 28 V PWM 型:电流模式 频率 - 开关:220kHz ~ 1MHz 电流 - 输出:600mA 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-SSOP（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:16-QSOP |
发布紧急采购，3分钟左右您将得到回复。