参数资料
| 型号： | ISL95872HRUZ-T |
| 厂商： | Intersil |
| 文件页数： | 15/17页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 16UTQFN |
| 标准包装： | 3,000 |
| PWM 型： | R4 |
| 输出数： | 1 |
| 频率 - 最大： | 300kHz |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -10°C ~ 100°C |
| 封装/外壳： | 16-UFQFN |
| 包装： | 带卷 (TR) |
ISL95872
VCC AND PVCC PINS
Place the decoupling capacitors as close as practical to the IC. In
particular, the PVCC decoupling capacitor should have a very
short and wide connection to the PGND pin. The VCC decoupling
capacitor should be referenced to GND pin.
EN AND PGOOD PINS
These are logic signals that are referenced to the GND pin. Treat
as a typical logic signal.
OCSET AND VO PINS
The current-sensing network consisting of R OCSET , R O , and C SEN
needs to be connected to the inductor pads for accurate
measurement of the DCR voltage drop. These components
however, should be located physically close to the OCSET and VO
pins with traces leading back to the inductor. It is critical that the
traces are shielded by the ground plane layer all the way to the
inductor pads. The procedure is the same for resistive current
sense.
FB, SREF, REFIN, AND RTN PINS
The input impedance of these pins is high, making it critical to
place the components connected to these pins as close as
possible to the IC.
LGATE, PGND, UGATE, BOOT, AND PHASE PINS
The signals going through these traces are high dv/dt and high
di/dt, with high peak charging and discharging current. The
PGND pin can only flow current from the gate-source charge of
the low-side MOSFETs when LGATE goes low. Ideally, route the
trace from the LGATE pin in parallel with the trace from the PGND
pin, route the trace from the UGATE pin in parallel with the trace
from the PHASE pin. In order to have more accurate zero-crossing
detection of inductor current, it is recommended to connect
Phase pin to the drain of the low-side MOSFETs with Kelvin
connection. These pairs of traces should be short, wide, and
away from other traces with high input impedance; weak signal
traces should not be in proximity with these traces on any layer.
15
FN7974.0
January 26, 2012
相关PDF资料 |
PDF描述 |
|---|---|
| ISL95874IRUZ-T | IC CTRLR PWM 1PHASE GPU 16UTQFN |
| ISL97516IUZ | IC REG BOOST ADJ 1A 8MSOP |
| ISL97519AIUZ-TK | IC REG BOOST ADJ 1A 8MSOP |
| ISL97519IUZ-T | IC REG BOOST ADJ 1A 8MSOP |
| ISL97522IRZ-TK | IC SUPPLY CTRL 4CH TFT-LCD 38QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL95873HRUZ-T | 功能描述:电流型 PWM 控制器 2-Bit PWM GPU Controller for Toshiba. Spin of ISL95872; 2.6 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL95874HRUZ-T | 功能描述:电流型 PWM 控制器 0/2 BIT PWM GPU CONTLR FOR NOTEBOOK RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL95874IRUZ-T | 功能描述:电流型 PWM 控制器 0/2 BIT PWM GPU CONTLR FOR NOTEBOOK RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL95875HRUZ-T | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL95875IRUZ-T | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。