- 您现在的位置：买卖IC网 > PDF目录239729 > IV80C52EXXX-25:RD (ATMEL CORP) 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP44 PDF资料下载
参数资料
| 型号： | IV80C52EXXX-25:RD |
| 厂商： | ATMEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP44 |
| 封装： | 1.40 MM HEIGHT, VQFP-44 |
| 文件页数： | 23/134页 |
| 文件大小： | 3805K |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页
119
8011Q–AVR–02/2013
ATmega164P/324P/644P
tion mode (WGMn3:0) bits must be set before the TOP value can be written to the ICRn
Register. When writing the ICRn Register the high byte must be written to the ICRnH I/O location
before the low byte is written to ICRnL.
For more information on how to access the 16-bit registers refer to ”Accessing 16-bit Registers”
13.6.1
Input Capture Trigger Source
The main trigger source for the Input Capture unit is the Input Capture pin (ICPn).
Timer/Counter1 can alternatively use the Analog Comparator output as trigger source for the
Input Capture unit. The Analog Comparator is selected as trigger source by setting the Analog
Comparator Input Capture (ACIC) bit in the Analog Comparator Control and Status Register
(ACSR). Be aware that changing trigger source can trigger a capture. The Input Capture Flag
must therefore be cleared after the change.
Both the Input Capture pin (ICPn) and the Analog Comparator output (ACO) inputs are sampled
using the same technique as for the Tn pin (Figure 13-1 on page 112). The edge detector is also
identical. However, when the noise canceler is enabled, additional logic is inserted before the
edge detector, which increases the delay by four system clock cycles. Note that the input of the
noise canceler and edge detector is always enabled unless the Timer/Counter is set in a Wave-
form Generation mode that uses ICRn to define TOP.
An Input Capture can be triggered by software by controlling the port of the ICPn pin.
13.6.2
Noise Canceler
The noise canceler improves noise immunity by using a simple digital filtering scheme. The
noise canceler input is monitored over four samples, and all four must be equal for changing the
output that in turn is used by the edge detector.
The noise canceler is enabled by setting the Input Capture Noise Canceler (ICNCn) bit in
Timer/Counter Control Register B (TCCRnB). When enabled the noise canceler introduces addi-
tional four system clock cycles of delay from a change applied to the input, to the update of the
ICRn Register. The noise canceler uses the system clock and is therefore not affected by the
prescaler.
13.6.3
Using the Input Capture Unit
The main challenge when using the Input Capture unit is to assign enough processor capacity
for handling the incoming events. The time between two events is critical. If the processor has
not read the captured value in the ICRn Register before the next event occurs, the ICRn will be
overwritten with a new value. In this case the result of the capture will be incorrect.
When using the Input Capture interrupt, the ICRn Register should be read as early in the inter-
rupt handler routine as possible. Even though the Input Capture interrupt has relatively high
priority, the maximum interrupt response time is dependent on the maximum number of clock
cycles it takes to handle any of the other interrupt requests.
Using the Input Capture unit in any mode of operation when the TOP value (resolution) is
actively changed during operation, is not recommended.
Measurement of an external signal’s duty cycle requires that the trigger edge is changed after
each capture. Changing the edge sensing must be done as early as possible after the ICRn
Register has been read. After a change of the edge, the Input Capture Flag (ICFn) must be
相关PDF资料 |
PDF描述 |
|---|---|
| IDT75T43100S66BS | SPECIALTY MICROPROCESSOR CIRCUIT, PBGA304 |
| IDT79RC64T575250DPI | 64-BIT, 250 MHz, RISC PROCESSOR, PQFP208 |
| IDT79R3081-40DL8 | 32-BIT, 40 MHz, RISC PROCESSOR, PQCC84 |
| ICS84325EM | 250 MHz, OTHER CLOCK GENERATOR, PDSO24 |
| ICS84427BM | 625 MHz, OTHER CLOCK GENERATOR, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IV-811MX | 制造商:Digital ID View 功能描述:8 CH H.264 DVR USB REMOTENO HDD 制造商:DIGITAL IDVIEW 功能描述:8 CH H.264 DVR USB REMOTE NO HDD |
| IV-811Z-960H-1000 | 制造商:Digital ID View 功能描述:8-Channel 960H i-Cloud Series DVR with 1TB HDD |
| IV-811Z-960H-500 | 制造商:Digital ID View 功能描述:8-Channel 960H i-Cloud Series DVR with 500GB HDD 制造商:DIGITAL IDVIEW 功能描述:8-CHNL ICLOUD 960H DVR 500GB HDD HDMI OUT |
| IV-811ZAECO-1000 | 制造商:Digital ID View 功能描述:8 Ch H.264 DVR D1 1Tbb Dvd |
| IV-811ZAECO-500 | 制造商:Digital ID View 功能描述:8 Ch H.264 DVR D1 500GB Dvd |
发布紧急采购，3分钟左右您将得到回复。