参数资料
| 型号： | KAD5510P-50Q72 |
| 厂商： | Intersil |
| 文件页数： | 14/29页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 500MSPS SGL 72-QFN |
| 产品培训模块： | High-Speed Analog-to-Digital Converters |
| 标准包装： | 1 |
| 系列： | FemtoCharge™ |
| 位数： | 10 |
| 采样率（每秒）： | 500M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 438mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 72-VFQFN 裸露焊盘 |
| 供应商设备封装： | 72-QFN（10x10） |
| 包装： | 托盘 |
| 输入数目和类型： | 1 个差分，单极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
21
FN6811.2
October 8, 2009
transitions to a high state after that point the state machine
will reset and terminate the data transfer.
2-byte and N-byte transfers, respectively. The operation for a
3-byte transfer can be inferred from these diagrams.
SPI Configuration
ADDRESS 0X00: CHIP_PORT_CONFIG
Bit ordering and SPI reset are controlled by this register. Bit
order can be selected as MSB to LSB (MSB first) or LSB to
MSB (LSB first) to accommodate various microcontrollers.
Bit 7 SDO Active
Bit 6 LSB First
Setting this bit high configures the SPI to interpret serial
data as arriving in LSB to MSB order.
Bit 5 Soft Reset
Setting this bit high resets all SPI registers to default
values.
Bit 4 Reserved
This bit should always be set high.
Bits 3:0 These bits should always mirror bits 4:7 to avoid
ambiguity in bit ordering.
ADDRESS 0X02: BURST_END
If a series of sequential registers are to be set, burst mode
can improve throughput by eliminating redundant addressing.
In 3-wire SPI mode the burst is ended by pulling the CSB pin
high. If the device is operated in 2-wire mode the CSB pin is
not available. In that case, setting the burst_end address
determines the end of the transfer. During a write operation,
the user must be cautious to transmit the correct number of
bytes based on the starting and ending addresses.
Bits 7:0 Burst End Address
This register value determines the ending address of the
burst data.
Device Information
ADDRESS 0X08: CHIP_ID
ADDRESS 0X09: CHIP_VERSION
The generic die identifier and a revision number,
respectively, can be read from these two registers.
Indexed Device Configuration/Control
ADDRESS 0X10: DEVICE_INDEX_A
Bits 1:0 ADC01, ADC00
Determines which ADC is addressed. Valid states for this
register are 0x01 or 0x10. The two ADC cores cannot be
adjusted concurrently.
A common SPI map, which can accommodate single-channel
or multi-channel devices, is used for all Intersil ADC products.
Certain configuration commands (identified as Indexed in the
SPI map) can be executed on a per-converter basis. This
register determines which converter is being addressed for an
Indexed command. It is important to note that only a single
converter can be addressed at a time.
This register defaults to 00h, indicating that no ADC is
addressed. Error code ‘AD’ is returned if any indexed register
is read from without properly setting device_index_A.
ADDRESS 0X20: OFFSET_COARSE
ADDRESS 0X21: OFFSET_FINE
The input offset of the ADC core can be adjusted in fine and
coarse steps. Both adjustments are made via an 8-bit word
as detailed in Table 7. The data format is two’s complement.
The default value of each register will be the result of the
self-calibration after initial power-up. If a register is to be
incremented or decremented, the user should first read the
register value then write the incremented or decremented
value back to the same register.
ADDRESS 0X22: GAIN_COARSE
ADDRESS 0X23: GAIN_MEDIUM
ADDRESS 0X24: GAIN_FINE
Gain of the ADC core can be adjusted in coarse, medium and
fine steps. Coarse gain is a 4-bit adjustment while medium
and fine are 8-bit. Multiple Coarse Gain Bits can be set for a
total adjustment range of ± 4.2%. ( ‘0011’
-4.2% and ‘1100’
+4.2% ) It is recommended to use one of the coarse gain
settings (-4.2%, -2.8%, -1.4%, 0, 1.4%, 2.8%, 4.2%) and
fine-tune the gain using the registers at 23h and 24h.
The default value of each register will be the result of the
self-calibration after initial power-up. If a register is to be
incremented or decremented, the user should first read the
TABLE 6. BYTE TRANSFER SELECTION
[W1:W0]
BYTES TRANSFERRED
00
1
01
2
10
3
11
4 or more
TABLE 7. OFFSET ADJUSTMENTS
PARAMETER
0x20[7:0]
COARSE OFFSET
0x21[7:0]
FINE OFFSET
Steps
255
-Full Scale (0x00)
-133LSB (-47mV)
-5LSB (-1.75mV)
Mid–Scale (0x80)
0.0LSB (0.0mV)
0.0LSB
+Full Scale (0xFF)
+133LSB (+47mV)
+5LSB (+1.75mV)
Nominal Step Size
1.04LSB (0.37mV)
0.04LSB (0.014mV)
KAD5510P-50
相关PDF资料 |
PDF描述 |
|---|---|
| KAD5512HP-17Q72 | IC ADC 12BIT 170MSPS SGL 72-QFN |
| KAD5512P-17Q72 | IC ADC 12BIT 170MSPS SGL 72-QFN |
| KAD5514P-12Q72 | IC ADC 14BIT 125MSPS SGL 72-QFN |
| KAD5610P-25Q72 | IC ADC 10BIT 250MSPS DUAL 72-QFN |
| KAD5612P-17Q72 | IC ADC 12BIT 170MSPS DUAL 72-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KAD5512HP | 制造商:未知厂家 制造商全称:未知厂家 功能描述:High Performance 12-Bit, 250/210/170/125MSPS ADC |
| KAD5512HP_09 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High Performance 12-Bit, 250/210/170/125MSPS ADC |
| KAD5512HP_0910 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High Performance 12-Bit, 250/210/170/125MSPS ADC |
| KAD5512HP-12Q48 | 功能描述:模数转换器 - ADC 12-BIT 125MSPS HI PERF SINGLE ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| KAD5512HP-12Q72 | 功能描述:模数转换器 - ADC 12-BIT 125MSPS HI PERF SINGLE ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。