- 您现在的位置：买卖IC网 > PDF目录17157 > KITMPR121EVM (Freescale Semiconductor)KIT EVALUATION MPR121 PDF资料下载
参数资料
| 型号： | KITMPR121EVM |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 10/27页 |
| 文件大小： | 0K |
| 描述： | KIT EVALUATION MPR121 |
| 产品培训模块： | MPR121: Low-Power Touch Sensor |
| 标准包装： | 1 |
| 传感器类型： | 近程 |
| 接口： | USB |
| 电源电压： | 5V，USB |
| 嵌入式： | 否 |
| 已供物品： | 4 个板，线缆，文档 |
| 已用 IC / 零件： | MPR121 |
| 产品目录页面： | 2808 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
MPR121
Sensors
18
Freescale Semiconductor, Inc.
SCTS: Skip Charge Time Search.
1: Skip CDTx search and update when autoconfiguration or autoreconfiguration, and current global CDT or CDTx are used
for respective channels. CDT or CDTx needs to be specified by the designer manually before operation. Setting the SCTS
to “1” results in a shorter time to complete autoconfiguration. This is useful for when the designer has obtained the correct
CDTx / CDT, and is confident that the current CDT and CDTx settings work in all conditions.
0: Both CDTx and CDCx will be searched and set by autoconfiguration and/or autoreconfiguration.
ACFIE: Auto-configuration fail interrupt enable. 1: Enable, 0: Disable
ARFIE: Auto-reconfiguration fail interrupt enable. 1: Enable, 0: Disable
OORIE: Out-of-range interrupt enable. 1: Enable, 0: Disable
USL: Up-Side Limit. This value sets the electrode data level up limit for the boundary check in autoconfiguration and
autoreconfiguration operation.
LSL: Low-Side Limit. This value sets the electrode data level low limit for the boundary check in autoconfiguration and
autoreconfiguration operation.
TL: Target Level. This value is the expected target electrode data level for autoconfiguration and autoreconfiguration, that is, after
successful autoconfiguration and autoreconfiguration, the measured electrode data level when untouched shall be close to the
TL value. TL shall be in between of USL and LSL.
The three parameters, USL, LSL and TL, are in the format similar to the baseline value; only the eight high bits are accessible
by user and the two low bits are set to zero automatically. The USL/LSL/TL data needs to be shifted left two bits before comparing
with the electrode data or the 10-bit baseline value.
In order to have a valid auto-configuration result, USL/LSL/TL values should follow the relation that 255 > USL > TL > LSL > 0.
For example, USL = 200, TL = USL*0.9 = 180, LSL = USL*0.5 = 100.
It is possible that in a end user environment, the channel differences may be significant. This is because the same set of USL/
LS/TL data is being used for all channels. It is important that the parameters not be set too close together. This makes it difficult
for the autoconfiguration to find a suitable charge setting for a specific channel. In this case, the electrode data might easily go
out of USL and LSL setting limits. Since the data is out-of-range, the channel status becomes OOR. If the channel is still OOR
after the autoconfiguration has been run, it may indicate that the settings for this channel have not yet been optimized. One
solution to this problem is to manually review the USL/LSL/TL settings. Another possible reason why the channel status could
be OOR is a problem with the channel itself. This could be caused by a short to ground, short to the power rail, or short to the
pad of the other channel.
For the TL setting, a good practice is to try to set it close to the USL. This so the charge field can be set to detect a weak touch.
On the other hand, the TL should not be set too close to the USL so that it is constantly exceeding the limit. For example, the
electrode data from the end user’s environment might have a much wider variance of readings. Some of the readings might
exceed the USL, causing the auto-configuration to fail. For this reason, if the amount of capacitance change in the end user
environment is significant, it is suggested that the USL and TL be set low enough to give some headroom for possible capacitance
variations.
Up-Side Limit Register (0x7D)
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Read
USL
Write
Low-Side Limit Register (0x7E)
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Read
LSL
Write
Target Level Register (0x7F)
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Read
TL
Write
相关PDF资料 |
PDF描述 |
|---|---|
| 22R473MC | IND 47UH 0.99A DRUM 7.8X7.5 SMD |
| LB3218T331K | INDUCTOR 330UH 10% 1207 SMD |
| SEK100M160ST | CAP ALUM 10UF 160V 20% RADIAL |
| KITMPR03XEVM | KIT EVAL FOR MPR03X |
| MIC4101YM | IC MOSFET DVR HALF BRIDGE 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KITMPR121EVM | 制造商:Freescale Semiconductor 功能描述:Sensor Toolbox Proximity Sensor Kit |
| KITMPVZ5004EVK | 功能描述:压力传感器开发工具 WATER LEVEL BOARD RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
| KITMPXA6115AEVB | 功能描述:压力传感器开发工具 Sensor Toolbx Pressu Sensor Developmt brd RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
| KITMPXSHOWEVK | 功能描述:压力传感器开发工具 PRESSURE SHOWBOARD RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
| KITMPXV5004DPEVB | 功能描述:压力传感器开发工具 MPXV5004 Dev Kit RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
发布紧急采购，3分钟左右您将得到回复。