- 您现在的位置：买卖IC网 > PDF目录17157 > KITMPR121EVM (Freescale Semiconductor)KIT EVALUATION MPR121 PDF资料下载
参数资料
| 型号： | KITMPR121EVM |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 13/27页 |
| 文件大小： | 0K |
| 描述： | KIT EVALUATION MPR121 |
| 产品培训模块： | MPR121: Low-Power Touch Sensor |
| 标准包装： | 1 |
| 传感器类型： | 近程 |
| 接口： | USB |
| 电源电压： | 5V，USB |
| 嵌入式： | 否 |
| 已供物品： | 4 个板，线缆，文档 |
| 已用 IC / 零件： | MPR121 |
| 产品目录页面： | 2808 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
MPR121
Sensors
20
Freescale Semiconductor, Inc.
These registers control GPIO and LED driver functions. D7~D0 bits correspond to GPIO and LED functions on ELE11~ ELE4
inputs respectively. When any of these ports are not used for electrode sensing, it can be used for GPIO or LED driver. The GPIO
control registers can be write at anytime regardless Stop Mode or Run mode. The configuration of the LED driver and GPIO
system is described with more detail in application note AN3894.
Note: The number of touch sensing electrodes, and therefore the number of GPIO ports left available is configured by the ECR
(0x5E) and GPIO Enable Register (0x77). ECR has higher priority and overrides the GPIO enabled in 0x77, that is when a pin is
enabled as GPIO but is also selected as electrode by ECR, the GPIO function is disabled immediately and it becomes an
electrode during Run Mode.
In the Stop Mode just after power-on reset, all electrodes and GPIO ports are in high impedance as all the GPIO ports are default
disabled and the electrodes are not enabled.
EN, DIR, CTL0, CTL1: GPIO enable and configuration bits, the functions are in description table below.
When the EN bit is set, the corresponding GPIO pin is enabled and the GPIO function is configured by CTL0, CTL1 and DIR bits.
When the port is used as an input, it can be configured as a normal logic input with high impedance (CTL0CTL1 = 2b00), input
with internal pull-down (CTL0CTL1 = 2b10) or pullup (CTL0CTL1 = 2b11). Note: the former may result in an unstable logic input
state if opened without fixed logic level input.
The GPIO output configuration can be configured as either push pull (CTL0CTL1 = 2b00) or open drain. When the GPIO is used
for LED drivers, the GPIO is set to high side only open drain (CTL0CTL1 = 2b11), which is can source up to 12 mA current into
the LED.
DAT: GPIO Data Register bits.
When a GPIO is enabled as an output, the GPIO port outputs the corresponding DAT bit level from GPIO Data Register (0x075).
The output level toggle remains on during any electrode charging. The level transition will occur after the ADC conversion takes
place. It is important to note that reading this register returns the content of the GPIO Data Register, (not a level of the port). When
a GPIO is configured as input, reading this register returns the latched input level of the corresponding port (not contents of the
GPIO Data Register). Writing to the DAT changes content of the register, but does not effect the input function.
SET: Writing a “1” to this bit will set the corresponding bit in the Data Register.
CLR: Writing a “1” to this bit will clear the corresponding bit in the Data Register.
TOG: Writing a “1” to this bit will toggle the corresponding bit in the Data Register
Writing “1” into the corresponding bits of GPIO Data Set Register, GPIO Data Clear Register, and GPIO Data Toggle Register will
set/clear/toggle contents of the corresponding DAT bit in Data Register. Writing “0” has no meaning. These registers allow any
individual port(s) to be set, cleared, or toggled individually without effecting other ports. It is important to note that reading these
registers returns the contents of the GPIO Data Register reading.
Direction Register(0x76)
DIR_E11
DIR_E10
DIR_E9
DIR_E8
DIR_E7
DIR_E6
DIR_E5
DIR_E4
Enable Register(0x77)
EN_E11
EN_E10
EN_E9
EN_E8
EN_E7
EN_E6
EN_E5
EN_E4
Data Set Register(0x78)
SET_E11
SET_E10
SET_E9
SET_E8
SET_E7
SET_E6
SET_E5
SET_E4
Data Clear Register(0x79)
CLR_E11
CLR_E10
CLR_E9
CLR_E8
CLR_E7
CLR_E6
CLR_E5
CLR_E4
Data Toggle Register(0x7A)
TOG_E11
TOG_E10
TOG_E11
TOG_E8
TOG_E7
TOG_E6
TOG_E5
TOG_E4
EN
DIR
CTL0:CTL1
Function Description
0
X
XX
GPIO function is disabled. Port is high-z state.
1
0
00
GPIO port becomes input port.
1
0
10
GPIO port becomes input port with internal pulldown.
1
0
11
GPIO port becomes input port with internal pullup.
1
0
01
Not defined yet (as same as CTL = 00).
1
00
GPIO port becomes CMOS output port.
1
11
GPIO port becomes high side only open drain output port for LED driver.
1
10
GPIO port becomes low side only open drain output port.
1
01
Not defined yet (as same as CTL = 00).
GPIO Registers (0x73~0x7A)
相关PDF资料 |
PDF描述 |
|---|---|
| 22R473MC | IND 47UH 0.99A DRUM 7.8X7.5 SMD |
| LB3218T331K | INDUCTOR 330UH 10% 1207 SMD |
| SEK100M160ST | CAP ALUM 10UF 160V 20% RADIAL |
| KITMPR03XEVM | KIT EVAL FOR MPR03X |
| MIC4101YM | IC MOSFET DVR HALF BRIDGE 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KITMPR121EVM | 制造商:Freescale Semiconductor 功能描述:Sensor Toolbox Proximity Sensor Kit |
| KITMPVZ5004EVK | 功能描述:压力传感器开发工具 WATER LEVEL BOARD RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
| KITMPXA6115AEVB | 功能描述:压力传感器开发工具 Sensor Toolbx Pressu Sensor Developmt brd RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
| KITMPXSHOWEVK | 功能描述:压力传感器开发工具 PRESSURE SHOWBOARD RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
| KITMPXV5004DPEVB | 功能描述:压力传感器开发工具 MPXV5004 Dev Kit RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
发布紧急采购，3分钟左右您将得到回复。