- 您现在的位置：买卖IC网 > PDF目录17157 > KITMPR121EVM (Freescale Semiconductor)KIT EVALUATION MPR121 PDF资料下载
参数资料
| 型号： | KITMPR121EVM |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 4/27页 |
| 文件大小： | 0K |
| 描述： | KIT EVALUATION MPR121 |
| 产品培训模块： | MPR121: Low-Power Touch Sensor |
| 标准包装： | 1 |
| 传感器类型： | 近程 |
| 接口： | USB |
| 电源电压： | 5V，USB |
| 嵌入式： | 否 |
| 已供物品： | 4 个板，线缆，文档 |
| 已用 IC / 零件： | MPR121 |
| 产品目录页面： | 2808 (CN2011-ZH PDF) |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
MPR121
Sensors
12
Freescale Semiconductor, Inc.
5.3
Electrode Filtered Data Register (0x04~0x1D)
The MPR121 provides filtered electrode output data for all 13 channels. The output data is 10-bit and comes from the internal
2nd stage filter output. The data range is 0~1024 or 0x000~0x400 in Hex. Bit 0~7 of the 10-bit data are stored in the low byte and
bit 9 and bit 8 are stored in the high byte. The data is the measured voltage on each channel and inversely proportional to the
capacitance on that channel.
These registers are read only and are updated every {ESI x SFI}. A multibyte read operation to read both LSB and MSB is
recommended to keep the data coherency (i.e, LSB and MSB matching). A multibyte reading of 0x00~0x2A returns results of a
single moment without mixing up old and new data.
5.4
Baseline Value Register (0x1E~0x2A)
Along with the 10-bit electrode filtered data output, each channel also has a 10-bit baseline value. The update rate of these
registers is {ESI x SFI} if baseline tracking operation is enabled. These values are the output of the internal baseline filter
operation tracking the slow-voltage variation of the background capacitance change. Touch/release detection is made based on
the comparison between the 10-bit electrode filtered data and the 10-bit baseline value.
Note: Although internally the baseline value is 10-bit, users can only access the 8 MSB of the 10-bit baseline value through the
baseline value registers. The read out from the baseline register must be left shift two bits before comparing it with the 10-bit
electrode data.
The Baseline Value register is writable in Stop Mode. Note: when the user writes into the baseline value register, the lower two
bits of the 10-bit baseline value are automatically cleared internally upon write operation. The Write to Baseline Value Register
by specific values can be sometimes useful if user wants to manipulate the touch/release status. For example, manually setting
the target channel from a touch locked state into a touch released state is easily done by setting the baseline value above the
signal data.
Refer to the Electrode Configuration Register (ECR, 0x5E) on how to control the on/off operation of baseline tracking and further
details on how the initial baseline data is loaded into Run Mode. Refer to Baseline Filtering Control registers(0x2B~0x2A) on how
to control the filtering of the baseline value.
5.5
Baseline Filtering Control Register (0x2B~0x40)
All12 of the electrode baseline values are controlled by the same set of filtering control registers, 0x2B ~ 0x35. The 13th channel
ELEPROX is controlled by registers 0x36 ~ 0x40. Both sets of registers have the same structure using three different scenarios;
rising, falling, and touched.
Rising is defined as when the electrode data is greater than the baseline value. Falling is defined as when the electrode data is
less than the baseline value. Touched is when the electrode is in touched status. For each scenario, the filtering characteristic is
further defined by four parameters: the maximum half delta (MHD), noise half delta (NHD), noise count limit (NCL) and filter delay
count limit (FDL). Note: there is no maximum half delta for the touched scenario.
Maximum Half Delta (MHD): Determines the largest magnitude of variation to pass through the baseline filter. The range of the
effective value is 1~63.
Noise Half Delta (NHD): Determines the incremental change when non-noise drift is detected. The range of the effective value
is 1~63.
Electrode Filtered Data Low Byte (0x04,0x06,...,0x1C)
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Read
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Write
—
Electrode Filtered Data High Byte (0x05,0x07,...,0x1D)
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Read
—
Bit 9
Bit 8
Write
—
Electrode Baseline Value (0x1E~0x2A)
Bit
D7
D6
D5
D4
D3
D2
D1
D0
Read
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Write
相关PDF资料 |
PDF描述 |
|---|---|
| 22R473MC | IND 47UH 0.99A DRUM 7.8X7.5 SMD |
| LB3218T331K | INDUCTOR 330UH 10% 1207 SMD |
| SEK100M160ST | CAP ALUM 10UF 160V 20% RADIAL |
| KITMPR03XEVM | KIT EVAL FOR MPR03X |
| MIC4101YM | IC MOSFET DVR HALF BRIDGE 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KITMPR121EVM | 制造商:Freescale Semiconductor 功能描述:Sensor Toolbox Proximity Sensor Kit |
| KITMPVZ5004EVK | 功能描述:压力传感器开发工具 WATER LEVEL BOARD RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
| KITMPXA6115AEVB | 功能描述:压力传感器开发工具 Sensor Toolbx Pressu Sensor Developmt brd RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
| KITMPXSHOWEVK | 功能描述:压力传感器开发工具 PRESSURE SHOWBOARD RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
| KITMPXV5004DPEVB | 功能描述:压力传感器开发工具 MPXV5004 Dev Kit RoHS:否 制造商:Freescale Semiconductor 工具用于评估:MPL3115A2 接口类型:USB 最大工作温度: |
发布紧急采购，3分钟左右您将得到回复。