- 您现在的位置：买卖IC网 > PDF目录22053 > KMC8113TMP3600V (Freescale Semiconductor)IC DSP 300/400MHZ 431FCPGA PDF资料下载
参数资料
| 型号： | KMC8113TMP3600V |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 32/44页 |
| 文件大小： | 0K |
| 描述： | IC DSP 300/400MHZ 431FCPGA |
| 标准包装： | 2 |
| 系列： | StarCore |
| 类型： | SC140 内核 |
| 接口： | 以太网，I²C，TDM，UART |
| 时钟速率： | 300MHz |
| 非易失内存： | 外部 |
| 芯片上RAM： | 1.436MB |
| 电压 - 输入/输出： | 3.30V |
| 电压 - 核心： | 1.10V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 431-BFBGA，FCBGA |
| 供应商设备封装： | 431-FCPBGA（20x20） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
MSC8113 Tri-Core Digital Signal Processor Data Sheet, Rev. 1
Hardware Design Considerations
Freescale Semiconductor
38
3
Hardware Design Considerations
The following sections discuss areas to consider when the MSC8113 device is designed into a system.
3.1
Use the following guidelines for start-up and power-down sequences:
Assert PORESET and TRST before applying power and keep the signals driven low until the power reaches the
required minimum power levels. This can be implemented via weak pull-down resistors.
CLKIN
can be held low or allowed to toggle during the beginning of the power-up sequence. However, CLKIN must
start toggling before the deassertion of PORESET and after both power supplies have reached nominal voltage levels.
If possible, bring up VDD/VCCSYN and VDDH together. If it is not possible, raise VDD/VCCSYN first and then bring up
VDDH. VDDH should not exceed VDD/VCCSYN until VDD/VCCSYN reaches its nominal voltage level. Similarly, bring both
voltage levels down together. If that is not possible reverse the power-up sequence, with VDDH going down first and
then VDD/VCCSYN.
Note:
This recommended power sequencing for the MSC8113 is different from the MSC8102.
External voltage applied to any input line must not exceed the I/O supply VDDH by more than 0.8 V at any time, including during
power-up. Some designs require pull-up voltages applied to selected input lines during power-up for configuration purposes.
This is an acceptable exception to the rule. However, each such input can draw up to 80 mA per input pin per device in the
system during start-up.
After power-up, VDDH must not exceed VDD/VCCSYN by more than 2.6 V.
3.2
When implementing a new design, use the guidelines described in the MSC8113 Design Checklist (AN3374 for optimal system
performance. MSC8122 and MSC8126 Power Circuit Design Recommendations and Examples (AN2937) provides detailed
design information.
Figure 33 shows the recommended power decoupling circuit for the core power supply. The voltage regulator and the
decoupling capacitors should supply the required device current without any drop in voltage on the device pins. The voltage on
the package pins should not drop below the minimum specified voltage level even for a very short spikes. This can be achieved
by using the following guidelines:
For the core supply, use a voltage regulator rated at 1.1 V with nominal rating of at least 3 A. This rating does not
reflect actual average current draw, but is recommended because it resists changes imposed by transient spikes and has
better voltage recovery time than supplies with lower current ratings.
Decouple the supply using low-ESR capacitors mounted as close as possible to the socket. Figure 33 shows three
capacitors in parallel to reduce the resistance. Three capacitors is a recommended minimum number. If possible, mount
at least one of the capacitors directly below the MSC8113 device.
Figure 33. Core Power Supply Decoupling
+
-
Power supply
or
Voltage Regulator
High frequency capacitors
(very low ESR and ESL)
Bulk/Tantalum capacitors
with low ESR and ESL
MSC8113
Maximum IR drop
of 15 mV at 1 A
Note: Use at least three capacitors.
Lmax = 2 cm
One 0.01 F capacitor
for every 3 core supply
(Imin = 3 A)
pads.
1.1 V
Each capacitor must be at least 150
μF.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2W2-CW-F1 | CONVERTER MOD DC/DC 15V 100W |
| 10018784-11112TLF | CONN PCI EXPRESS 98POS VERT PCB |
| 10018784-11102TLF | CONN PCI EXPRESS 98POS VERT PCB |
| AMC22DRXI | CONN EDGECARD 44POS .100 DIP SLD |
| VE-2WR-CW-F4 | CONVERTER MOD DC/DC 7.5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KMC8113TMP4800V | 功能描述:IC DSP 300/400MHZ 431FCPGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:StarCore 标准包装:40 系列:TMS320DM64x, DaVinci™ 类型:定点 接口:I²C，McASP，McBSP 时钟速率:400MHz 非易失内存:外部 芯片上RAM:160kB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:0°C ~ 90°C 安装类型:表面贴装 封装/外壳:548-BBGA，FCBGA 供应商设备封装:548-FCBGA（27x27） 包装:托盘 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| KMC8113TVT3600V | 功能描述:IC DSP 300/400MHZ 431FCPGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:StarCore 标准包装:40 系列:TMS320DM64x, DaVinci™ 类型:定点 接口:I²C，McASP，McBSP 时钟速率:400MHz 非易失内存:外部 芯片上RAM:160kB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:0°C ~ 90°C 安装类型:表面贴装 封装/外壳:548-BBGA，FCBGA 供应商设备封装:548-FCBGA（27x27） 包装:托盘 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| KMC8113TVT4800V | 功能描述:IC DSP 300/400MHZ 431FCPGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:StarCore 标准包装:40 系列:TMS320DM64x, DaVinci™ 类型:定点 接口:I²C，McASP，McBSP 时钟速率:400MHz 非易失内存:外部 芯片上RAM:160kB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:0°C ~ 90°C 安装类型:表面贴装 封装/外壳:548-BBGA，FCBGA 供应商设备封装:548-FCBGA（27x27） 包装:托盘 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| KMC811E2CFN2 | 制造商:Freescale Semiconductor 功能描述:MCU - Bulk |
| KMC811E2CP2 | 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述: |
发布紧急采购，3分钟左右您将得到回复。