- 您现在的位置：买卖IC网 > PDF目录11595 > KSZ8863RLLI (Micrel Inc)IC ETHERNET SWITCH 3PORT 48-LQFP PDF资料下载
参数资料
| 型号： | KSZ8863RLLI |
| 厂商： | Micrel Inc |
| 文件页数： | 73/106页 |
| 文件大小： | 0K |
| 描述： | IC ETHERNET SWITCH 3PORT 48-LQFP |
| 标准包装： | 250 |
| 控制器类型： | 以太网开关控制器 |
| 接口： | MII |
| 电源电压： | 1.8V，2.5V，3.3V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 托盘 |
| 配用： | 576-3868-ND - BOARD EVALUATION FOR KSZ8863RLL |
| 其它名称： | 576-3752 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页当前第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页
PIC16C72 Series
DS39016A-page 68
Preliminary
1998 Microchip Technology Inc.
10.10
Interrupts
The PIC16C72/CR72 has 8 sources of interrupt. The
interrupt control register (INTCON) records individual
interrupt requests in ag bits. It also has individual and
global interrupt enable bits.
A global interrupt enable bit, GIE (INTCON<7>)
enables (if set) all un-masked interrupts or disables (if
cleared) all interrupts. When bit GIE is enabled, and an
interrupt’s ag bit and mask bit are set, the interrupt will
vector immediately. Individual interrupts can be dis-
abled through their corresponding enable bits in vari-
ous
registers.
Individual
interrupt
bits
are
set
regardless of the status of the GIE bit. The GIE bit is
cleared on reset.
The “return from interrupt” instruction, RETFIE, exits
the interrupt routine as well as sets the GIE bit, which
re-enables interrupts.
The RB0/INT pin interrupt, the RB port change inter-
rupt and the TMR0 overow interrupt ags are con-
tained in the INTCON register.
The peripheral interrupt ags are contained in the spe-
cial function registers PIR1 and PIR2. The correspond-
ing interrupt enable bits are contained in special
function registers PIE1 and PIE2, and the peripheral
interrupt enable bit is contained in special function reg-
ister INTCON.
When an interrupt is responded to, the GIE bit is
cleared to disable any further interrupt, the return
address is pushed onto the stack and the PC is loaded
with 0004h. Once in the interrupt service routine the
source(s) of the interrupt can be determined by polling
the interrupt ag bits. The interrupt ag bit(s) must be
cleared in software before re-enabling interrupts to
avoid recursive interrupts.
For external interrupt events, such as the INT pin or
PORTB change interrupt, the interrupt latency will be
three or four instruction cycles. The exact latency
depends when the interrupt event occurs. The latency
is the same for one or two cycle instructions. Individual
interrupt ag bits are set regardless of the status of
their corresponding mask bit or the GIE bit
10.10.1 INT INTERRUPT
External interrupt on RB0/INT pin is edge triggered:
either rising if bit INTEDG (OPTION<6>) is set, or fall-
ing, if the INTEDG bit is clear. When a valid edge
appears
on
the
RB0/INT
pin,
ag
bit
INTF
(INTCON<1>) is set. This interrupt can be disabled by
clearing enable bit INTE (INTCON<4>). Flag bit INTF
must be cleared in software in the interrupt service rou-
tine before re-enabling this interrupt. The INT interrupt
can wake-up the processor from SLEEP, if bit INTE was
set prior to going into SLEEP. The status of global inter-
rupt enable bit GIE decides whether or not the proces-
sor branches to the interrupt vector following wake-up.
See Section 10.13 for details on SLEEP mode.
10.10.2 TMR0 INTERRUPT
An overow (FFh
→ 00h) in the TMR0 register will set
ag bit T0IF (INTCON<2>). The interrupt can be
enabled/disabled by setting/clearing enable bit T0IE
(INTCON<5>). (Section 4.0)
10.10.3 PORTB INTCON CHANGE
An input change on PORTB<7:4> sets ag bit RBIF
(INTCON<0>). The interrupt can be enabled/disabled
by setting/clearing enable bit RBIE (INTCON<4>).
FIGURE 10-11: INTERRUPT LOGIC
Note:
Individual interrupt ag bits are set regard-
less of the status of their corresponding
mask bit or the GIE bit.
ADIF
ADIE
SSPIF
SSPIE
CCP1IF
CCP1IE
TMR2IF
TMR2IE
TMR1IF
TMR1IE
T0IF
T0IE
INTF
INTE
RBIF
RBIE
GIE
PEIE
Wake-up (If in SLEEP mode)
Interrupt to CPU
Clear GIE bit
相关PDF资料 |
PDF描述 |
|---|---|
| V72A3V3C264BG3 | CONVERTER MOD DC/DC 3.3V 264W |
| KSZ8851SNL TR | IC CTLR MAC/PHY NON-PCI 32-MLF |
| PIC16F676-E/SL | IC MCU FLASH 1KX14 W/AD 14SOIC |
| LTC4278IDKD#PBF | IC PD IEEE 802.3AT 25.5W 32-DFN |
| KSZ8873MML | IC ETHERNET SWITCH 3PORT 64-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8864CNXCA | 功能描述:Ethernet Controller 10/100 Base-T/TX PHY MII, RMII Interface 64-QFN (8x8) 制造商:microchip technology 系列:- 包装:托盘 零件状态:有效 协议:以太网 功能:控制器 接口:MII，RMII 标准:10/100 Base-T/TX PHY 电压 - 电源:1.8V，2.5V，3.3V 电流 - 电源:- 工作温度:0°C ~ 70°C 封装/外壳:64-VFQFN 裸露焊盘 供应商器件封装:64-QFN（8x8） 标准包装:348 |
| KSZ8864RMN | 功能描述:以太网 IC 4-Port 10/100 Ethernet Switch w/ 2x PHYs and 2x MAC Interface RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8864RMN-EVAL | 功能描述:以太网开发工具 4-Port 10/100 Ethernet Switch w/ 2x PHYs and 2x MAC Interface - Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8864RMNI | 功能描述:以太网 IC 4-Port 10/100 Ethernet Switch w/ 2x PHYs and 2x MAC Interface - Industrial Temp RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8864RMNU | 功能描述:以太网 IC 4-Port 10/100BT Switch with MII/RMII (Automotive) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。