- 您现在的位置：买卖IC网 > PDF目录67755 > LC5511D POWER FACTOR CONTROLLER, 18 kHz SWITCHING FREQ-MAX, DIP7 PDF资料下载
参数资料
| 型号： | LC5511D |
| 元件分类： | 稳压器 |
| 英文描述： | POWER FACTOR CONTROLLER, 18 kHz SWITCHING FREQ-MAX, DIP7 |
| 封装： | DIP-8/7 |
| 文件页数： | 29/40页 |
| 文件大小： | 888K |
| 代理商： | LC5511D |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
35
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
28106.02
Here is the example of design specification and calculation:
Given:
AC input voltage: 85 to 265 VAC
Output power: 40 W
Transformer primary winding: 40 T
Transformer auxiliary winding: 6 T
IDP at the minimum AC input voltage: 3.0 A
I'DP at the maximum AC input voltage where the output power
of the maximum AC input voltage becomes the same as that
limited by OCP at the minimum AC input voltage: 1.9 A
ROCP = 0.2 Ω
R3 = 220 Ω
DX1 forward voltage: 0.8 V
OCP input compensation starting voltage: 120 VAC
1. Calculate Efw1 at 120 VAC input:
=
Efw1
NP
ND
==
40
6
× VIN(AC)× √2
× 120 √2
25.4 (V)
(16)
Thus, select 27 V as the Zener value for DZX1.
2. The compensation current, I, is calculated using equation 10:
=
I
0.2 (Ω)
220 (Ω)
= 1 (mA)
(3.0 (A) – 1.9 (A)) ×
3. RX1 can be calculated using equation 14:
=
RX1
40 (T)
1 (mA)
28.4 (kΩ)
6 (T) × 265 (VAC)√2 – (27 (V) + 0.8 (V))
Thus, select RX1 = 27 kΩ out of the E12 resistor standard value.
Finally, ensure that these values work to achieve the target output
power through experiments, and adjust them if necessary.
Thermal Shutdown Protection
Thermal Shutdown protection is activated at TJ(TSD) = 135°C
(min). When it activates, the IC enters a latched mode.
Maximum On-Time Limiting Function
The maximum on-time, set at tON(MAX) = 40 μs (figure 50), limits
lower side switching frequency, and it minimizes audible noise
from the transformer at low AC input or during transient periods
such as at switching AC mains on or off.
Ensure that the actual on-time at the minimum AC input and the
maximum load condition does not reach tON(MAX) = 40 μs. If that
does happen, redesign the transformer, such as by reducing the
primary inductance or reducing the duty cycle by lowering the
turns ratio of NP / NS.
Design Considerations
Peripheral Components
Choose appropriate components that are matched to actual use
conditions.
Consider design margins for ratings of ripple current, voltage,
and temperature in selecting the output capacitor. A low-
impedance capacitor, designed to be tolerant against high ripple
current, designed for a SMPS, is recommended.
Consider design margins for temperature rise, resulting from
copper losses and core losses, in designing or selecting a
transformer.
Switching current contains a high frequency component that
causes the skin effect; therefore, consider a current density of
3 to 4 A/mm2 and select a wire gauge based on rms current. In
the event further temperature measurement is necessary and it is
necessary to increase surface area of the wire, try the following
measures:
Increase the quantity of parallel wires
Use litz wire
Increase the diameter of the wires
Choose a low equivalent series inductance and high surge
tolerant type for the current sensing resistor. If a high
inductance type is used, because of the high frequency current
running through it, it may cause malfunctioning.
Transformer Design
The transformer design is the same as for an RCC (ringing choke
converter, or self-oscillation flyback converter) transformer
design. However, a quasi-resonant operation includes a certain
delay to turn-on, so duty cycle must be compensated.
I
D
V
DS
time
Maximum
On-Time
Figure 50. Maximum On-Time
相关PDF资料 |
PDF描述 |
|---|---|
| LC5521D | 2.5 A POWER FACTOR CONTROLLER, 18 kHz SWITCHING FREQ-MAX, DIP7 |
| LC72137 | PLL FREQUENCY SYNTHESIZER, 40 MHz, PDIP22 |
| LC72137M | PLL FREQUENCY SYNTHESIZER, 40 MHz, PDSO20 |
| LC72137 | PLL FREQUENCY SYNTHESIZER, 40 MHz, PDIP22 |
| LC72137M | PLL FREQUENCY SYNTHESIZER, 40 MHz, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LC5512B-10F256C | 功能描述:CPLD - 复杂可编程逻辑器件 PROGRAM EXPANDED LOG RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
| LC5512B-10F256I | 功能描述:CPLD - 复杂可编程逻辑器件 PROGRAM EXPANDED LOG RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
| LC5512B-10F484C | 功能描述:CPLD - 复杂可编程逻辑器件 Use ispMACH 4000B RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
| LC5512B-10F484I | 功能描述:CPLD - 复杂可编程逻辑器件 Use ispMACH 4000B RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
| LC5512B-10Q208C | 功能描述:CPLD - 复杂可编程逻辑器件 Use ispMACH 4000B RoHS:否 制造商:Lattice 系列: 存储类型:EEPROM 大电池数量:128 最大工作频率:333 MHz 延迟时间:2.7 ns 可编程输入/输出端数量:64 工作电源电压:3.3 V 最大工作温度:+ 90 C 最小工作温度:0 C 封装 / 箱体:TQFP-100 |
发布紧急采购，3分钟左右您将得到回复。