参数资料
| 型号： | LC75808W-E |
| 厂商： | ON Semiconductor |
| 文件页数： | 23/38页 |
| 文件大小： | 0K |
| 描述： | IC LCD DISPLAY DRIVER 100SQFP |
| 标准包装： | 60 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
? If a key is pressed for longer than 800T(s)(where T= fOSC ) the LC75808W outputs a key data read request (a
LC75808W
3. In sleep mode
? The pins KS1 to KS6 are set to high or low by the KC1 to KC6 bits in the control data.
? If a key on one of the lines corresponding to a KS1 to KS6 pin which is set high is pressed, the oscillator on the
OSC pin is started and a key scan is performed. Keys are scanned until all keys are released. Multiple key presses
are recognized by determining whether multiple key data bits are set.
1
low level on DO) to the controller. The controller acknowledges this request and reads the key data. However, if
CE is high during a serial data transfer, DO will be set high.
? After the controller reads the key data, the key data read request is cleared (DO is set high) and the LC75808W
performs another key scan. However, this dose not clear sleep mode. Also note that DO, being an open-drain
output, requires a pull-up resistor (between 1 k Ω and 10 k Ω ).
? Sleep mode key scan example
Example: When the control data bits KC1 to KC5 are 0, KC6 is 1, and SP is 1. (sleep with only KS6 high)
[L]
KS1
[L]
[L]
[L]
[L]
[H]
KS2
KS3
KS4
KS5
KS6
When any one of these keys is pressed,
the oscillator on the OSC pin is started
and the keys are scanned.
*4
KI1
KI2
KI3
KI4
KI5
A12913
Note: * 4. These diodes are required to reliable recognize multiple key presses on the KS6 line when sleep mode state
with only KS6 high, as in the above example. That is, these diodes prevent incorrect operations due to sneak
currents in the KS6 key scan output signal when keys on the KS1 to KS5 lines are pressed at the same time.
Key input
(KS6 line)
Key scan
CE
800T [s]
800T [s]
Serial data
transfer
Serial data
transfer
Key address(43H)
Serial data
transfer
Key address
T=
1
fosc
DI
DO
Key data read request
Key data read
Key data read
Key data read request
A12914
Multiple Key Presses
Although the LC75808W is capable of key scanning without inserting diodes for dual key presses, triple key presses on
the KI1 to KI5 input pin lines, or multiple key presses on the KS1 to KS6 output pin lines, multiple presses other than
these cases may result in keys that were not pressed recognized as having been pressed. Therefore, a diode must be
inserted in series with each key. Applications that do not recognize multiple key presses of three or more keys should
check the key data for three or more 1 bits and ignore such data.
No.6370-23/38
相关PDF资料 |
PDF描述 |
|---|---|
| LC75812PT-8565-H | IC LCD DISPLAY DRIVER 100TQFP |
| LC75813E-E | IC LCD DISPLAY DRIVER 100QLP |
| LC75832W-E | IC LCD DISPLAY DRIVER 64SQFP |
| LC75841PE-H | IC LCD DISPLAY DRIVER 36QFP |
| LC75844M-E | IC LCD DISPLAY DRIVER MFP36SDJ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LC75808WS-E | 功能描述:LCD 驱动器 RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| LC75808W-SH-E | 功能描述:LCD 驱动器 RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| LC75809PT-H | 制造商:ON Semiconductor 功能描述:LCD DISPLAY DRIVER - Trays |
| LC75809PTH-H | 制造商:ON Semiconductor 功能描述:LCD DISPLAY DRIVER - Trays |
| LC75809PTS-H | 制造商:ON Semiconductor 功能描述:LCD DISPLAY DRIVER - Trays |
发布紧急采购，3分钟左右您将得到回复。