- 您现在的位置：买卖IC网 > PDF目录30743 > LM1253AAE/NA (NATIONAL SEMICONDUCTOR CORP) ON-SCREEN DISPLAY IC, PDIP28 PDF资料下载
参数资料
| 型号： | LM1253AAE/NA |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 画面叠加 |
| 英文描述： | ON-SCREEN DISPLAY IC, PDIP28 |
| 封装： | 0.600 INCH, PLASTIC, DIP-28 |
| 文件页数： | 61/61页 |
| 文件大小： | 1671K |
| 代理商： | LM1253AAE/NA |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页当前第61页
Pin Descriptions (Continued)
as the DC clamp control capacitors. A value of 0.0047 F is
used in the demo boards. The schematic shown in
Figure 29
which has a series resistance of 33
and clamp diodes to
V
CC and ground should be used to protect the LM1253A
from ESD. A good ground should be between the input
connector and the LM1253A. The video traces should be
kept short.
Figure 29 shows the external schematic of pins 4,
5, and 6,
Figure 14 shows the internal schematic of pins 4, 5,
and 6.
Pin 7 — Analog Ground Ground for the video section of the
LM1253A. All ground pins of the LM1253A should be con-
nected together by a ground plane under the LM1253A. See
Figure 31, which shows a sample layout.
Pin 8 — Analog Supply 5V supply for the video section of
the preamp. A 0.1 F capacitor should be connected be-
tween pin 7 and pin 8, as close as possible to the LM1253A.
A 100 F capacitor should also be connected between pin 7
and pin 8.
Pin 9 — Analog Supply 5V supply for the PLL section of the
LM1253A. A 0.1 F capacitor should be connected between
pin 9 and pin 7, as close as possible to the LM1253A.
Pin 10 — PLL Ground Ground for the PLL section of the
LM1253A. Only the PLL components connected to pin 11
should be connected to this ground pin. Pin 10 should also
be connected to the ground plane under the LM1253A. All
ground pins of the LM1253A should be connected together
by a ground plane under the LM1253A. See
Figure 31, which
shows a sample layout.
Pin 11 — PLL C A resistor capacitor network is connected to
this pin. It is used to convert the charge current of the charge
pump of the PLL into a voltage that is used to control the
variable oscillator. These components should be located
very close to the LM1253A with a short ground trace to pin
10.
The recommended values are R28 = 6.2 k
, C23 = 0.1 F,
and C33 = 2.2 nF. When these component values are used
the range and gain values in
Table 12 can be loaded into
register 843Eh.
An example layout is shown in
Figure 31, Figure 29 shows
the external schematic of pin 11,
Figure 15 shows the inter-
nal schematic.
Pin 12 — ABL The Auto Beam Limit control reduces the gain
of the video amplifiers in response to a control voltage
proportional to the CRT beam current. The ABL acts on all
three channels in an identical manner. This is required for
CRT life and X-ray protection. The beam current limit circuit
application is as shown in
Figure 7: when no current is being
drawn by the EHT supply, current flows from the supply rail
through the ABL resistor and into the ABL input of the IC. The
IC clamps the input voltage to a low impedance voltage
source (the 5V supply rail).
When current is drawn from the EHT supply, the current
passes through the ABL resistor, and reduces the current
flowing into the ABL input of the IC.
When the EHT current is high enough, the current flowing
into the ABL input of the IC drops to zero. This current level
determines the ABL threshold and is given by:
Where:
V
S is the external supply (usually the CRT driver supply rail,
about 80V)
V
ABL TH is the threshold ABL voltage of the IC
R
ABL is the ABL resistor value
I
ABL is the ABL limit
When the voltage on the ABL input drops below the ABL
threshold of the pre-amp, the gain of the pre-amp decreases,
which is shown in
Figure 8, which reduces the beam current.
A feedback loop is thus established which acts to prevent the
average beam current exceeding I
ABL.
Figure 29 shows the external schematic of pin 12, Figure 16
shows the internal schematic.
DS101265-12
FIGURE 7. ABL
LM1253A
www.national.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| LM1267NA/NOPB | 3 CHANNEL, VIDEO PREAMPLIFIER, PDIP24 |
| LM1269NA/NOPB | 3 CHANNEL, VIDEO PREAMPLIFIER, PDIP24 |
| LM1276AAA/NA | 1 CHANNEL, VIDEO PREAMPLIFIER, PDIP28 |
| LM1279AN/NOPB | 3 CHANNEL, VIDEO AMPLIFIER, PDIP20 |
| LM1279N/NOPB | 1 CHANNEL, VIDEO AMPLIFIER, PDIP20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM1253AN | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Monolithic Triple 180 MHz I2C CRT Pre-amp With Integrated Analog On Screen Display (OSD) Generator |
| LM-1256 | 制造商:ROHM 制造商全称:Rohm 功能描述:16 x 16 matrix displays |
| LM-1256_1 | 制造商:ROHM 制造商全称:Rohm 功能描述:16】16 matrix displays |
| LM-1256LB1 | 制造商:ROHM 制造商全称:Rohm 功能描述:16】16 matrix displays |
| LM125AN | 制造商:NSC 制造商全称:National Semiconductor 功能描述:VOLTAGE REGULATORS |
发布紧急采购，3分钟左右您将得到回复。