- 您现在的位置：买卖IC网 > PDF目录98001 > LMX2364TMX/NOPB (NATIONAL SEMICONDUCTOR CORP) PLL FREQUENCY SYNTHESIZER, 2600 MHz, PDSO24 PDF资料下载
参数资料
| 型号： | LMX2364TMX/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | PLL合成/DDS/VCOs |
| 英文描述： | PLL FREQUENCY SYNTHESIZER, 2600 MHz, PDSO24 |
| 封装： | TSSOP-24 |
| 文件页数： | 15/39页 |
| 文件大小： | 694K |
| 代理商： | LMX2364TMX/NOPB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
Input Impedance
20050676
The above block diagram shows the test procedure measur-
ing the input impedance for the LMX2364. This applies to the
FinRF, FinIF, OSCinRF, and OSCinIF pins. The input imped-
ance of the CSP and the TSSOP package should always be
assumed to be different, until proven otherwise. The basic
test procedure is to calibrate the network analyzer, ensure
that the part is powered up, and then measure the input
impedance.
The network analyzer can be calibrated by using either
calibration standards or by soldering resistors directly to the
evaluation board. An open can be implemented by putting no
resistor, a short can be implemented by usinga0ohm
resistor, and a short can be implemented by using two 100
ohm resistors in parallel. Note that no DC blocking capacitor
is used for this test procedure. This is done with the PLL
removed from the PCB. This requires the use of a clamp
down fixture that may not always be generally available. If no
clamp down fixture is available, then this procedure can be
done by calibrating up to the point where the DC blocking
capacitor usually is, and then adding a 0 ohm resistor back
for the actual measurement.
Once that the network analyzer is calibrated, it is necessary
to ensure that the PLL is powered up. This can be done by
toggling the power down bits (RF_PD and IF_PD) and ob-
serving that the current consumption indeed increases when
the bit is disabled. Sometimes it may be necessary to apply
a signal to the OSCinIF pin in order to program the part. If
this is necessary, disconnect the signal once it is established
that the part is powered up.
It is useful to know the input impedance of the PLL for the
purposes of debugging RF problems and designing match-
ing networks. Another use of knowing this parameter is make
the trace width on the PCB such that the input impedance of
this trace matches the real part of the input impedance of the
PLL frequency of operation. In general, it is good practice to
keep trace lengths short and make designs that are relatively
resistant to variations in the input impedance of the PLL.
LMX2364
www.national.com
22
相关PDF资料 |
PDF描述 |
|---|---|
| LMX2372MDC | PLL FREQUENCY SYNTHESIZER, 1200 MHz, UUC |
| LMX2531LQ1500EX | PLL FREQUENCY SYNTHESIZER, 80 MHz, QCC36 |
| LMZ12003EXTTZX | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PSSO7 |
| LMZ12003EXTTZ | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PSSO7 |
| LMZ12003EXTTZE | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PSSO7 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LMX2370 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:PLLatinum⑩ Dual Frequency Synthesizer for RF Personal Communications |
| LMX2370SLBX | 功能描述:IC FREQ SYNTH DUAL 24LAMINATECSP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:PLLatinum™ 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LMX2370SLDX | 功能描述:IC FREQ SYNTH DUAL 24LAMINATECSP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:PLLatinum™ 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LMX2370TM | 功能描述:IC FREQ SYNTH DL 2.5GHZ 20TSSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:PLLatinum™ 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| LMX2370TMX | 功能描述:IC FREQ SYNTH DL 2.5GHZ 20-TSSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:PLLatinum™ 标准包装:39 系列:- 类型:* PLL:带旁路 输入:时钟 输出:时钟 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 频率 - 最大:170MHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
发布紧急采购，3分钟左右您将得到回复。