- 您现在的位置：买卖IC网 > Datasheet目录988 > LP5521TMEV (National Semiconductor)EVAL BOARD FOR LP5521 Datasheet资料下载
参数资料
| 型号： | LP5521TMEV |
| 厂商： | National Semiconductor |
| 文件页数： | 14/44页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR LP5521 |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | Q5109809 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
SNVS441F – JANUARY 2007 – REVISED FEBRUAY 2013
LED FORWARD VOLTAGE MONITORING
When charge pump automatic mode selection is enabled, voltages over LED drivers are monitored. If drivers do
not have enough headroom, charge pump gain is set to 1.5x. Driver saturation monitor does not have a fixed
voltage limit, since saturation voltage is a function of temperature and current. Charge pump gain is set to 1x,
when battery voltage is high enough to supply all LEDs.
In automatic gain change mode, charge pump is switched to bypass mode (1x), when LEDs are inactive for over
50 ms.
Charge pump gain control utilizes digital filtering to prevent supply voltage disturbances from triggering gain
changes. If R driver current source is connected to battery (address 08H, bit R_TO_BATT = 1) voltage
monitoring is disabled in R output, but still functional in B and G output.
LED forward voltage monitoring and gain control block diagram is shown below.
Charge
Pump
VOUT
Current
Source
V OFS
PWM
Saturation
MODE
Monitor
R/G/B
Comparator
Digital
Filter
Control
Registers
Program
Memory
Command
Look-ahead
Mode
Control
Figure 24. Voltage monitoring block diagram for one output
LED DRIVER OPERATIONAL DESCRIPTION
The LP5521 LED drivers are constant current sources with 8-bit PWM control. Output current can be
programmed with I 2 C register up to 25.5 mA. Current setting resolution is 100 μ A (8-bit control).
R driver has two modes: current source can be connected to battery (V DD ) or to charge pump output. If current
source is connected to battery, automatic charge pump gain control is not used for this output. This approach
provides better efficiency when LED with low V F is connected to R driver, and battery voltage is high enough to
drive this LED in all conditions. R driver mode can be selected with I 2 C register bit. When address 08H, bit
R_TO_BATT = 1, R current source is connected to battery. When it is 0 (default), R current source is connected
to charge pump same way as in G and B drivers. G and B drivers are always connected to charge pump output.
Some LED configuration examples are given in table below. When LEDs with low V F are used, charge pump can
be operating in bypass mode (1x). This eliminates the need of having double drivers for all outputs; one
connected to battery and another connected to charge pump output. When LP5521 is driving a RGB LED, R
channel can be configured to use battery power. This configuration increases power efficiency by minimizing the
voltage drop across the LED driver.
Table 2. LED configuration examples
Configuration
R output to BATT
R output to CP
CP Mode
RGB LED with low V F red
3 x low V F LED
3 x white LED
1 x low V F LED (R output)
X
X
X
X
Auto (1x or 1.5x)
1x
Auto (1x or 1.5x)
Disabled
PWM frequency is either 256 Hz or 558 Hz, frequency is set with PWM_HF bit in register 08H. When PWM_HF
is 0, then the frequency is 256 Hz, and when bit is 1 then the PWM frequency is 558 Hz. Brightness adjustment
is either linear or logarithmic. This can be set with register 00H LOG_EN bit. When LOG_EN = 0 linear
adjustment scale is used, and when LOG_EN = 1 logarithmic scale is used. By using logarithmic scale the visual
effect seems linear to the eye. Register control bits are presented in following tables:
14
Product Folder Links: LP5521
Copyright ? 2007–2013, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| LPS0300H1000JB | RESISTOR HEAT SINK 100 OHM 300W |
| LPS0600H4R70JB | RESISTOR HEAT SINK 4.7 OHM 600W |
| LPS0800H1000JB | RESISTOR HEAT SINK 100 OHM 800W |
| LPS1100H47R0JB | RESISTOR HEAT SINK 47 OHM 1100W |
| LR1000 | LINE CONDITIONER 1000W 4OUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LP5521TMX | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Programmable Three Channel LED Driver |
| LP5521TMX/NOPB | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LP5521YQ | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Programmable Three Channel LED Driver |
| LP5521YQ/NOPB | 功能描述:LED照明驱动器 3 Ch Prog Led Driver LLP RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LP5521YQ/S7002688 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
发布紧急采购，3分钟左右您将得到回复。