- 您现在的位置：买卖IC网 > Datasheet目录988 > LP5521TMEV (National Semiconductor)EVAL BOARD FOR LP5521 Datasheet资料下载
参数资料
| 型号： | LP5521TMEV |
| 厂商： | National Semiconductor |
| 文件页数： | 17/44页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR LP5521 |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | Q5109809 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
SNVS441F – JANUARY 2007 – REVISED FEBRUAY 2013
Table 7. R Channel PC register (09H), G CHANNEL PC register (0AH), B CHANNEL PC register (0BH)
Name
PC
Bit
3:0
Description
Program counter value from 0 to 15d
Table 8. ENABLE register (00H)
Name
R_EXEC
G_EXEC
B_EXEC
Bit
5:4
3:2
1:0
Description
R channel program execution
00b = Hold: Wait until current command is finished then stop while EXEC mode is hold. PC can be read
or written only in this mode.
01b = Step: Execute instruction defined by current R channel PC value, increment PC and change
R_EXEC to 00b (Hold)
10b = Run: Start at program counter value defined by current R channel PC value
11b = Execute instruction defined by current R channel PC value and change R_EXEC to 00b (Hold)
G channel program execution
00b = Hold: Wait until current command is finished then stop while EXEC mode is hold. PC can be read
or written only in this mode.
01b = Step: Execute instruction defined by current G channel PC value, increment PC and change
G_EXEC to 00b (Hold)
10b = Run: Start at program counter value defined by current G channel PC value
11b = Execute instruction defined by current G channel PC value and change G_EXEC to 00b (Hold)
B channel program execution
00b = Hold: Wait until current command is finished then stop while EXEC mode is hold. PC can be read
or written only in this mode.
01b = Step: Execute instruction defined by current B channel PC value, increment PC and change
B_EXEC to 00b (Hold)
10b = Run: Start at program counter value defined by current B channel PC value
11b = Execute instruction defined by current B channel PC value and change B_EXEC to 00b (Hold)
EXEC registers are synchronized to 32 kHz clock. Delay between consecutive I 2 C writes to ENABLE register
(00H) need to be longer than 488 μ s (typ.).
DIRECT Control
When R, G or B channel mode is set to 11b, the LP5521 drivers work in direct control mode. LP5521 LED
channels can be controlled independently through I 2 C. For each channel there is a PWM control register and a
output current control register. With output current control register is set what is the maximum output current with
8-bit resolution, step size is 100 μ A. Duty cycle can be set with 8-bit resolution. Direct control mode resets
respective channel’s PC. PWM control bits are presented in following table:
Table 9. R_PWM register (02H), G_PWM register (03H), B_PWM register (04H):
Name
PWM
Bit
7:0
Description
LED PWM value during direct control operation mode
0000 0000b = 0%
1111 1111b = 100%
If charge pump automatic gain change is used in this mode, then PWM values need to be written 0 before
changing the drivers’ operation mode to disabled (00b) to ensure proper automatic gain change operation.
LED CONTROLLER PROGRAMMING COMMANDS
LP5521 has three independent programmable channels (R, G, B). Trigger connections between channels are
common for all channels. All channels have own program memories for storing complex patterns. Brightness
control and patterns are done with 8-bit PWM control (256 steps) to get accurate and smooth color control.
Program execution is timed with 32 768 Hz clock. This clock can be generated internally or external 32 kHz clock
can be connected to CLK_32K pin. Using external clock enables synchronization of LED timing to this clock
rather than internal clock. Selection of the clock is made with address 08H bits INT_CLK_EN and CLK_DET_EN.
See EXTERNAL CLOCK DETECTION for details.
Supported commands are listed in the table below. Command compiler is available for easy sequence
programming. With Command compiler it is possible to write sequences with simple ASCII commands,
which are then converted to binary or hex format. See application note "LP5521 Programming
Considerations" for examples of Command compiler usage.
Copyright ? 2007–2013, Texas Instruments Incorporated
Product Folder Links: LP5521
17
相关PDF资料 |
PDF描述 |
|---|---|
| LPS0300H1000JB | RESISTOR HEAT SINK 100 OHM 300W |
| LPS0600H4R70JB | RESISTOR HEAT SINK 4.7 OHM 600W |
| LPS0800H1000JB | RESISTOR HEAT SINK 100 OHM 800W |
| LPS1100H47R0JB | RESISTOR HEAT SINK 47 OHM 1100W |
| LR1000 | LINE CONDITIONER 1000W 4OUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LP5521TMX | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Programmable Three Channel LED Driver |
| LP5521TMX/NOPB | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LP5521YQ | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Programmable Three Channel LED Driver |
| LP5521YQ/NOPB | 功能描述:LED照明驱动器 3 Ch Prog Led Driver LLP RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LP5521YQ/S7002688 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
发布紧急采购，3分钟左右您将得到回复。