- 您现在的位置：买卖IC网 > PDF目录14461 > LT1425IS#PBF (Linear Technology)IC REG FLYBK ISOLATED .2A 16SOIC PDF资料下载
参数资料
| 型号： | LT1425IS#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/20页 |
| 文件大小： | 0K |
| 描述： | IC REG FLYBK ISOLATED .2A 16SOIC |
| 标准包装： | 50 |
| 类型： | 回扫，隔离 |
| 输出数： | 1 |
| 输入电压： | 2.8 V ~ 20 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 285kHz |
| 电流 - 输出： | 200mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 16-SOIC |
| 产品目录页面： | 1327 (CN2011-ZH PDF) |
LT1425
APPLICATIO N S I N FOR M ATIO N
amount when output switch current is zero. Please refer
to Figure 1 which shows nominal reference current shift
at zero load for a range of R OCOMP values. Example: for
a load compensation resistor of 12k, the graph indi-
cates a 1.0% shift in reference current. The R FB resistor
value should be adjusted down by about 1.0% to
restore the original target output voltage.
2
1
integers, e.g., 1:1, 2:1, 3:2, etc. can be employed which
yield more freedom in setting total turns and mutual
inductance. Turns ratio can then be chosen on the basis of
desired duty cycle. However, remember that the input
supply voltage plus the secondary-to-primary referred
version of the flyback pulse (including leakage spike) must
not exceed the allowed output switch breakdown rating.
Leakage Inductance
Transformer leakage inductance (on either the primary or
secondary) causes a spike after output switch turn-off.
This is increasingly prominent at higher load currents
where more stored energy must be dissipated. In many
cases a “snubber” circuit will be required to avoid over-
voltage breakdown at the output switch node. LTC’s
Application Note 19 is a good reference on snubber
design.
0
1
10 100
R OCOMP (k ? )
1000
In situations where the flyback pulse extends beyond the
enable delay time, the output voltage regulation will be
1425 F01
Figure 1
In less critical applications, or when output current
remains relatively constant, the load compensation func-
tion may be deemed unnecessary. In such cases, a
reduced component solution may be obtained as follows:
Leave the R OCOMP node open (R OCOMP = ∞ ), and replace
the filter capacitor normally on the R CCOMP node with a
short to ground.
TRANSFORMER DESIGN CONSIDERATIONS
Transformer specification and design is perhaps the most
critical part of applying the LT1425 successfully. In addi-
tion to the usual list of caveats dealing with high frequency
isolated power supply transformer design, the following
information should prove useful.
Turns Ratio
Note that due to the use of an R FB /R REF resistor ratio to set
output voltage, the user has relative freedom in selecting
transformer turns ratio to suit a given application. In other
words, “screwball” turns ratios like “1.736:1.0” can scru-
pulously be avoided! In contrast, simpler ratios of small
12
affected to some degree. It is important to realize that the
feedback system has a deliberately limited input range,
roughly ± 50mV referred to the R REF node, and this works
to the user’s advantage in rejecting large, i.e., higher
voltage leakage spikes. In other words, once a leakage
spike is several volts in amplitude, a further increase in
amplitude has little effect on the feedback system. So the
user is generally advised to arrange the snubber circuit to
clamp at as high a voltage as comfortably possible,
observing switch breakdown, such that leakage spike
duration is as short as possible.
As a rough guide, total leakage inductances of several
percent (of mutual inductance) or less may require a
snubber, but exhibit little to no regulation error due to
leakage spike behavior. Inductances from several percent
up to perhaps ten percent cause increasing regulation
error.
Severe leakage inductances in the double digit percentage
range should be avoided if at all possible as there is a
potential for abrupt loss of control at high load current.
This curious condition potentially occurs when the leak-
age spike becomes such a large portion of the flyback
waveform that the processing circuitry is fooled into
thinking that the leakage spike itself is the real flyback
相关PDF资料 |
PDF描述 |
|---|---|
| HBM24DSXN | CONN EDGECARD 48POS DIP .156 SLD |
| RBC30DRAH-S734 | CONN EDGECARD 60POS .100 R/A PCB |
| HCM24DSXH | CONN EDGECARD 48POS DIP .156 SLD |
| HBM24DSXH | CONN EDGECARD 48POS DIP .156 SLD |
| HCM24DRXN | CONN EDGECARD 48POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT14-2-FP | 制造商:Thomas & Betts 功能描述:LT14-2 FOOD PROCESSINGOUTLET BOX 制造商:Thomas & Betts 功能描述:Fittings Gang Box 0.75inch Female Aluminum |
| LT1431 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Synchronous Rectifier Driver for Forward Converters |
| LT1431_10 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Programmable Reference |
| LT1431C | 制造商:LINER 制造商全称:Linear Technology 功能描述:Programmable Reference |
| LT1431CN8 | 功能描述:IC VREF SHUNT ADJ 8-PDIP RoHS:否 类别:集成电路 (IC) >> PMIC - 电压基准 系列:- 产品培训模块:Voltage Reference Basics 标准包装:100 系列:- 基准类型:旁路，精度 输出电压:4.096V 容差:±0.075% 温度系数:50ppm/°C 输入电压:- 通道数:1 电流 - 阴极:1µA 电流 - 静态:- 电流 - 输出:10mA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。