- 您现在的位置：买卖IC网 > PDF目录44982 > LT1766HGN#PBF (LINEAR TECHNOLOGY CORP) 3 A SWITCHING REGULATOR, 228 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | LT1766HGN#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 3 A SWITCHING REGULATOR, 228 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | 0.150 INCH, LEAD FREE, PLASTIC, SSOP-16 |
| 文件页数： | 10/28页 |
| 文件大小： | 284K |
| 代理商： | LT1766HGN#PBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
18
LT1766/LT1766-5
1766fb
APPLICATIO S I FOR ATIO
WU
UU
rating. A ground plane should always be used under the
switcher circuitry to prevent interplane coupling and over-
all noise.
The VC and FB components should be kept as far away as
possible from the switch and boost nodes. The LT1766
pinout has been designed to aid in this. The ground for
these components should be separated from the switch
current path. Failure to do so will result in poor stability or
subharmonic like oscillation.
Board layout also has a significant effect on thermal
resistance. Pins 1, 8, 9 and 16, GND, are a continuous
copper plate that runs under the LT1766 die. This is the
best thermal path for heat out of the package. Reducing
the thermal resistance from Pins 1, 8, 9 and 16 onto the
board will reduce die temperature and increase the power
capability of the LT1766. This is achieved by providing as
much copper area as possible around these pins. Adding
multiple solder filled feedthroughs under and around
these four corner pins to the ground plane will also help.
Similar treatment to the catch diode and coil terminations
will reduce any additional heating effects. For the FE
package, the exposed pad (Pin 17) should be soldered to
the copper ground plane underneath the device.
PARASITIC RESONANCE
Resonance or “ringing” may sometimes be seen on the
switch node (see Figure 7). Very high frequency ringing
following switch rise time is caused by switch/diode/input
capacitor lead inductance and diode capacitance. Schot-
tky diodes have very high “Q” junction capacitance that
can ring for many cycles when excited at high frequency.
If total lead length for the input capacitor, diode and
switch path is 1 inch, the inductance will be approximately
25nH. At switch off, this will produce a spike across the
NPN output device in addition to the input voltage. At
higher currents this spike can be in the order of 10V to 20V
or higher with a poor layout, potentially exceeding the
absolute max switch voltage. The path around switch,
catch diode and input capacitor must be kept as short as
possible to ensure reliable operation. When looking at this,
a >100MHz oscilloscope must be used, and waveforms
should be observed on the leads of the package. This
Figure 6. Suggested Layout
GND
SHDN
SYNC
GND
BOOST
VIN
SW
PLACE FEEDTHROUGH AROUND
GROUND PINS (4 CORNERS) FOR
GOOD THERMAL CONDUCTIVITY
LT1766
C3
C1
D1
C2
D2
R2
R1
1766 F06
CFB
CF
RC
CC
L1
MINIMIZE LT1766
C3-D1 LOOP
GND
BIAS
FB
VC
CONNECT TO
GROUND PLANE
KELVIN SENSE
VOUT
KEEP FB AND VC COMPONENTS
AWAY FROM HIGH FREQUENCY,
HIGH CURRENT COMPONENTS
FOR THE FE PACKAGE, THE
EXPOSED PAD (PIN 17) SHOULD
BE PROPERLY SOLDERED TO
THE GROUND PLANE.
NOTE: BOOST AND BIAS
COPPER TRACES ARE ON
A SEPARATE LAYER FROM
THE GROUND PLANE
GND
VOUT
VIN
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
相关PDF资料 |
PDF描述 |
|---|---|
| LT1776IS8#TR | 1 A SWITCHING REGULATOR, 230 kHz SWITCHING FREQ-MAX, PDSO8 |
| LT1871IMS-7#PBF | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LT1871IMS-7 | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LT1871EMS-7#PBF | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LT1871EMS-7 | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1766IFE | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1766IFE#PBF | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LT1766IFE#PBF | 制造商:Linear Technology 功能描述:IC STEP-DOWN REGULATOR 16-TSSOP |
| LT1766IFE#TR | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LT1766IFE#TRPBF | 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
发布紧急采购，3分钟左右您将得到回复。