- 您现在的位置：买卖IC网 > PDF目录1823 > LT1943EFE#TRPBF (Linear Technology)IC REG SW QUAD TFT LCD 28-TSSOP PDF资料下载
参数资料
| 型号： | LT1943EFE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/20页 |
| 文件大小： | 0K |
| 描述： | IC REG SW QUAD TFT LCD 28-TSSOP |
| 标准包装： | 2,000 |
| 应用： | 转换器，TFT，LCD |
| 输入电压： | 4.5 V ~ 22 V |
| 输出数： | 4 |
| 输出电压： | 1.25 V ~ 40 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 包装： | 带卷 (TR) |
LT1943
OPERATIO
must have low impedance at the switching frequency to do
this effectively and it must have an adequate ripple current
rating. The input capacitor RMS current can be calculated
from the step-down output voltage and current, and the
input voltage:
solution is to either clamp the input voltage or dampen the
tank circuit by adding a lossy capacitor (an electrolytic) in
parallel with the ceramic capacitor. For details, see Appli-
cation Note 88.
Soft-Start and Shutdown
< OUT
C INRMS = I OUT ?
V OUT ( V IN – V 0 UT )
V IN
I
2
The RUN/SS (Run/Soft-Start) pin is used to place the
switching regulators and the internal bias circuits in shut-
down mode. It also provides a soft-start function, along
and is largest when V IN = 2 V OUT (50% duty cycle). The
ripple current contribution from the other channels will be
minimal. Considering that the maximum load current from
switcher 1 is ~2.8A, RMS ripple current will always be less
than 1.4A.
The high frequency of the LT1943 reduces the energy
storage requirements of the input capacitor, so that the
capacitance required is less than 10 μ F. The combination
of small size and low impedance (low equivalent series
resistance or ESR) of ceramic capacitors makes them the
preferred choice. The low ESR results in very low voltage
ripple. Ceramic capacitors can handle larger magnitudes
of ripple current than other capacitor types of the same
value. Use X5R and X7R types.
An alternative to a high value ceramic capacitor is a lower
value along with a larger electrolytic capacitor, for ex-
ample a 1 μ F ceramic capacitor in parallel with a low ESR
tantalum capacitor. For the electrolytic capacitor, a value
larger than 10 μ F will be required to meet the ESR and
ripple current requirements. Because the input capacitor
is likely to see high surge currents when the input source
is applied, only consider a tantalum capacitor if it has the
appropriate surge current rating. The manufacturer may
also recommend operation below the rated voltage of the
capacitor. Be sure to place the 1 μ F ceramic as close as
possible to the V IN and GND pins on the IC for optimal
noise immunity.
A final caution is in order regarding the use of ceramic
capacitors at the input. A ceramic input capacitor can
combine with stray inductance to form a resonant tank
circuit. If power is applied quickly (for example by plug-
ging the circuit into a live power source), this tank can ring,
doubling the input voltage and damaging the LT1943. The
with SS-234. If the RUN/SS is pulled to ground, the
LT1943 enters its shutdown mode with all regulators off
and quiescent current reduced to ~35 μ A. An internal
1.7 μ A current source pulls up on the RUN/SS and SS-234
pins. If the RUN/SS pin reaches ~0.8V, the internal bias
circuits start and the quiescent currents increase to their
nominal levels.
If a capacitor is tied from the RUN/SS or SS-234 pins to
ground, then the internal pull-up current will generate a
voltage ramp on these pins. This voltage clamps the V C
pin, limiting the peak switch current and therefore input
current during start-up. The RUN/SS pin clamps V C1 , and
the SS-234 pin clamps the V C2 , V C3 , and V C4 pins. A good
value for the soft-start capacitors is C OUT /10,000, where
C OUT is the value of the largest output capacitor.
To shut down SW2, SW3, and SW4, pull the SS-234 pin to
ground with an open drain or collector.
If the shutdown and soft-start features are not used, leave
the RUN/SS and SS-234 pins floating.
V ON Pin Considerations
The V ON pin is the delayed output for switching regulator
3. When the C T pin reaches 1.1V, the output disconnect
PNP turns on, connecting V ON to E3. The V ON pin is current
limited, and will protect the LT1943 and input source from
a shorted output. However, if the V ON pin is charged to a
high output voltage, and then shorted to ground through
a long wire, unpredictable results can occur. The resonant
tank circuit created by the inductance of the long wire and
the capacitance at the V ON pin can ring the V ON pin several
volts below ground. This can lead to large and potentially
damaging currents internal to the LT1943. If the V ON
output may be shorted after being fully charged, there
1943fa
16
相关PDF资料 |
PDF描述 |
|---|---|
| LT1944-1EMS#TR | IC REG BST ADJ 0.1A/175MA 10MSOP |
| LT1945IMS#TRPBF | IC REG MULTI CONFIG ADJ 10MSOP |
| LT1946EMS8E#TRPBF | IC REG BOOST 1.5A 8MSOP |
| LT1947EMSE#TRPBF | IC REG TFT-LCD ADJ 10-MSOP |
| LT1949IS8#TRPBF | IC REG BOOST ADJ 1A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1944 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Quad DCDC Converter for Triple Outputs TFT Supply Plus LED Driver |
| LT1944-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Micropower Step-Up DC/DC Converter |
| LT1944-1EMS | 功能描述:IC REG BST ADJ 0.1A/175MA 10MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LT1944-1EMS#PBF | 功能描述:IC REG BST ADJ 0.1A/175MA 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT1944-1EMS#TR | 功能描述:IC REG BST ADJ 0.1A/175MA 10MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。