- 您现在的位置：买卖IC网 > PDF目录1823 > LT1943EFE#TRPBF (Linear Technology)IC REG SW QUAD TFT LCD 28-TSSOP PDF资料下载
参数资料
| 型号： | LT1943EFE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC REG SW QUAD TFT LCD 28-TSSOP |
| 标准包装： | 2,000 |
| 应用： | 转换器，TFT，LCD |
| 输入电压： | 4.5 V ~ 22 V |
| 输出数： | 4 |
| 输出电压： | 1.25 V ~ 40 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 28-TSSOP 裸露焊盘 |
| 包装： | 带卷 (TR) |
LT1943
PI FU CTIO S
GND (Pins 1, 20, Exposed Pad Pin 29): Ground. Tie both
GND pins and the exposed pad directly to a local ground
plane. The ground metal to the exposed pad should be as
wide as possible for better heat dissipation. Multiple vias
(to ground plane under the ground backplane) placed
close to the exposed pad can further aid in reducing
thermal resistance.
VC1 (Pin 2): Switching Regulator 1 Error Amplifier Com-
pensation. Connect a resistor/capacitor network in series
with this pin.
VC2 (Pin 3): Error Amplifier Compensation for Switcher 2.
Connect a resistor/capacitor network in series with this
pin.
FB1 (Pin 4): Switching Regulator 1 Feedback. Tie the
resistor divider tap to this pin and set V LOGIC according to
V LOGIC = 1.25 ? (1 + R2/R1). Reference designators refer
to Figure 1.
FB2 (Pin 5): Feedback for Switch 2. Tie the resistor divider
tap to this pin and set AV DD according to AV DD = 1.25 ?
(1 + R6/R5).
FB3 (Pin 6): Switching Regulator 3 Feedback. Tie the
resistor divider tap to this pin and set V ON according to
V ON = 1.25 ? (1 + R9/R8) – 150mV.
NFB4 (Pin 7): Switching Regulator 4 Negative Feedback.
Switcher 4 can be used to generate a positive or negative
output. When regulating a negative output, tie the resistor
divider tap to this pin. Negative output voltage can be set
by the equation V OFF = –1.245 ? (R3/R4) with R4 set to 10k.
Tie the NFB4 pin to FB4 for positive output voltages.
FB4 (Pin 8): Feedback for Switch 4. When generating a
positive voltage from switch 4, tie the resistor divider tap
to this pin. When generating a negative voltage, tie a 10k
resistor between FB4 and NFB4 (R4).
VC3 (Pin 9): Switching Regulator 3 Error Amplifier Com-
pensation. Connect a resistor/capacitor network in series
with this pin.
VC4 (Pin 10): Switching Regulator 4 Error Amplifier
Compensation. Connect a resistor/capacitor network in
series with this pin.
SGND (Pin 11): Signal Ground. Return ground trace from
the FB resistor networks and V C pin compensation compo-
nents directly to this pin and then tie to ground.
BOOST (Pin 12): The BOOST pin is used to provide a drive
voltage, higher than V IN , to the switch 1 drive circuit.
SW1 (Pins 13, 14): The SW1 pins are the emitter of the
internal NPN bipolar power transistor for switching regu-
lator 1. These pins must be tied together for proper
operation. Connect these pins to the inductor, catch diode
and boost capacitor.
V IN (Pins 15, 16): The V IN pins supply current to the
LT1943’s internal regulator and to the internal power
transistor for switch 1. These pins must be tied together
and locally bypassed.
SS-234 (Pin 17): This is the soft-start pin for switching
regulators 2, 3 and 4. Place a soft-start capacitor here to
limit start-up inrush current and output voltage ramp rate.
When the BIAS pin reaches 2.8V, a 1.7 μ A current source
begins charging the capacitor. When the capacitor voltage
reaches 0.8V, switches 2, 3 and 4 turn on and begin
switching. For slower start-up, use a larger capacitor.
When this pin is pulled to ground, switches 2, 3 and 4 are
disabled. For complete shutdown, tie RUN-SS to ground.
RUN-SS (Pin 18): This is the soft-start pin for switching
regulator 1. Place a soft-start capacitor here to limit start-
up inrush current and output voltage ramp rate. When
power is applied to the V IN pin, a 1.7 μ A current source
charges the capacitor. When the voltage at this pin reaches
0.8V, switch 1 turns on and begins switching. For slower
start-up, use a larger capacitor. For complete shutdown,
tie RUN-SS to ground.
SW4 (Pin 19): This is the collector of the internal NPN
bipolar power transistor for switching regulator 4. Mini-
mize metal trace area at this pin to keep EMI down.
1943fa
7
相关PDF资料 |
PDF描述 |
|---|---|
| LT1944-1EMS#TR | IC REG BST ADJ 0.1A/175MA 10MSOP |
| LT1945IMS#TRPBF | IC REG MULTI CONFIG ADJ 10MSOP |
| LT1946EMS8E#TRPBF | IC REG BOOST 1.5A 8MSOP |
| LT1947EMSE#TRPBF | IC REG TFT-LCD ADJ 10-MSOP |
| LT1949IS8#TRPBF | IC REG BOOST ADJ 1A 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1944 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Quad DCDC Converter for Triple Outputs TFT Supply Plus LED Driver |
| LT1944-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Micropower Step-Up DC/DC Converter |
| LT1944-1EMS | 功能描述:IC REG BST ADJ 0.1A/175MA 10MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LT1944-1EMS#PBF | 功能描述:IC REG BST ADJ 0.1A/175MA 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT1944-1EMS#TR | 功能描述:IC REG BST ADJ 0.1A/175MA 10MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。