- 您现在的位置：买卖IC网 > PDF目录14826 > LT3581EMSE#PBF (Linear Technology)IC REG MULTI CONFIG ADJ 16MSOP PDF资料下载
参数资料
| 型号： | LT3581EMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/36页 |
| 文件大小： | 0K |
| 描述： | IC REG MULTI CONFIG ADJ 16MSOP |
| 标准包装： | 37 |
| 类型： | 升压（升压），反相，回扫，Sepic |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.22 V ~ 42 V |
| 输入电压： | 2.5 V ~ 22 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz ~ 2.5MHz |
| 电流 - 输出： | 3.3A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-MSOP，裸露焊盘 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LT3581
PIN FUNCTIONS
(DFN/MSOP)
R FB = ? OUT
? V – 1 . 215 V ?
? 83 . 3 ? 10 – 6 ? ?
R FB = ? OUT
? | V | + 9 mV ?
? 83 . 3 ? 10 – 6 ? ?
FB (Pin 1/Pin 1): Positive and Negative Feedback Pin. For
a Boost or Inverting Converter, tie a resistor from the FB
pin to V OUT according to the following equations:
; Boost or SEPIC C onverter
; Inv e rting Converter
V C (Pin 2/Pin 2): Error Amplifier Output Pin. Tie external
compensation network to this pin.
GATE (Pin 3/Pin 3): PMOS Gate Drive Pin. The GATE pin
is a pull-down current source, used to drive the gate of
an external PMOS for output short circuit protection or
output disconnect. The GATE pin current increases linearly
with the SS pin’s voltage, with a maximum pull-down
current of 933μA at SS voltages exceeding 500mV. Note
that if the SS voltage is greater than 500mV and the GATE
pin voltage is less than 2V, then the GATE pin looks like
a 2kΩ impedance to ground. See the Appendix for more
information.
FAULT (Pin 4/Pin 4): Fault Indication Pin. This active low,
bidirectional pin can either be pulled low (below 750mV)
by an external source, or internally by the chip to indicate a
fault. When pulled low, this pin causes the power switches
to turn off, the GATE pin to become high impedance, the
CLKOUT pin to become disabled, and the SS pin to go
through a charge/discharge sequence. The end/absence
of a fault is indicated when the voltage on this pin exceeds
1V. A pull-up resistor or current source is needed on this
pin to pull it above 1V in the absence of a fault.
V IN (Pin 5/Pin 5): Input Supply Pin. Must be locally by-
passed.
SW1 (Pins 6, 7/Pins 6,7, 8): Master Switch Pin. This is the
collector of the internal master NPN power switch.
Minimize the metal trace area connected to this pin to
minimize EMI.
CLKOUT (Pin 10/Pin 12): Clock Output Pin. Use this pin
to synchronize one or more other compatible switching
regulator ICs to the LT3581. The clock that this pin outputs
runs at the same frequency as the internal oscillator of the
part or as the SYNC pin. CLKOUT may also be used as a
temperature monitor since the CLKOUT pin’s duty cycle
varies linearly with the part’s junction temperature. Note
that the CLKOUT pin is only meant to drive capacitive
loads up to 50pF.
SHDN (Pin 11/Pin 13): Shutdown Pin. In conjunction
with the UVLO (undervoltage lockout) circuit, this pin is
used to enable/disable the chip and restart the soft-start
sequence. Drive below 300mV to disable the chip. Drive
above 1.33V (typical) to activate the chip and restart the
soft-start sequence. Do not float this pin.
RT (Pin 12/Pin 14): Timing Resistor Pin. Adjusts the
LT3581’s switching frequency. Place a resistor from this
pin to ground to set the frequency to a fixed free running
level. Do not float this pin.
SS (Pin 13/Pin 15): Soft-Start Pin. Place a soft-start
capacitor here. Upon start-up, the SS pin will be charged
by a (nominally) 250k resistor to about 2.1V. During a
fault, the SS pin will be slowly charged up and eventually
discharged as part of a timeout sequence (see the State
Diagram for more information on the SS pin’s role during
a fault event).
SYNC (Pin 14/Pin 16): To synchronize the switching
frequency to an outside clock, simply drive this pin with
a clock. The high voltage level of the clock must exceed
1.3V, and the low level must be less than 0.4V. Drive this
pin to less than 0.4V to revert to the internal free running
clock. See the Applications Information section for more
information.
GND (Exposed Pad Pin 15/Exposed Pad Pin 17): Ground.
Exposed pad must be soldered directly to local ground
plane.
SW2 (Pins 8, 9/Pins 9, 10, 11): Slave Switch Pin. This
is the collector of the internal slave NPN power switch.
Minimize the metal trace area connected to this pin to
minimize EMI.
3581fa
For more information www.linear.com/LT3581
7
相关PDF资料 |
PDF描述 |
|---|---|
| LT1777CS#PBF | IC REG BUCK ADJ 0.7A 16SOIC |
| EBA32DCBI | CONN EDGECARD 64POS R/A .125 SLD |
| 381LR121M400H032 | CAP ALUM 120UF 400V 20% SNAP |
| 2000-4R7-H-RC | INDUCTOR TOROID 4.7UH 20% HORZ |
| LTC3642EMS8E-3.3#PBF | IC REG BUCK SYNC 3.3V 50MA 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3581EMSE-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:3.3A Boost/Inverting DC/DC Converter with Fault Protection |
| LT3581HDE#PBF | 制造商:Linear Technology 功能描述:IC REG MULTI CONFIG ADJ 14DFN |
| LT3581HDE#TRPBF | 制造商:Linear Technology 功能描述:IC REG MULTI CONFIG ADJ 14DFN |
| LT3581IDE#PBF | 功能描述:IC REG MULTI CONFIG ADJ 14DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3581IDE#TRPBF | 功能描述:IC REG MULTI CONFIG ADJ 14DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。