- 您现在的位置：买卖IC网 > PDF目录30768 > LT3751IUFD#TRPBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 PDF资料下载
参数资料
| 型号： | LT3751IUFD#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
| 封装： | 4 X 5 MM, LEAD FREE, PLASTIC, QFN-20 |
| 文件页数： | 11/34页 |
| 文件大小： | 403K |
| 代理商： | LT3751IUFD#TRPBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LT3751
19
3751fb
APPLICATIONS INFORMATION
Gate Driver Operation
The LT3751 gate driver has an internal, selectable 10.5V
or 5.6V clamp with up to 2A current capability (using
LVGATE). For 10.5V operation, tie CLAMP pin to ground,
and for 5.6V operation, tie the CLAMP pin to the VCC pin.
Choose a clamp voltage that does not exceed the NMOS
manufacturer’s maximum VGS ratings. The 5.6V clamp
can also be used to reduce LT3751 power dissipation
and increase efciency when using logic-level FETs. The
typical gate driver overshoot voltage is 0.5V above the
clamp voltage.
The LT3751’s gate driver also incorporates a PMOS pull-up
device via the LVGATE pin. The PMOS pull-up driver should
only be used for VCC applications of 8V or below. Operating
LVGATE with VCC above 8V will cause permanent damage
to the part. LVGATE is active when tied to HVGATE and
allows rail-to-rail gate driver operation. This is especially
useful for low VCC applications, allowing better NMOS
drive capability. It also provides the fastest rise times,
given the larger 2A current capability verses 1.5A when
using only HVGATE.
Output Diode Selection
The output diode(s) are selected based on the maximum
repetitive reverse voltage (VRRM) and the average forward
current (IF(AV)). The output diode’s VRRM should exceed
VOUT + N VTRANS. The output diode’s IF(AV) should exceed
IPK/2N,theaverageshort-circuitcurrent.Theaveragediode
current is also a function of the output voltage.
Table 4. Recommended Output Diodes
MANUFACTURER
PART NUMBER
IF(AV) (A)
VRRM (V)
TRR (ns)
PACKAGE
Central Semiconductor
www.centralsemi.com
CMR1U-10M
CMSH2-60M
CMSH5-40
1
2
5
1000
60
40
100
SMA
SMC
Fairchild Semiconductor
www.fairchildsemi.com
ES3J
ES1G
ES1J
3
1
600
400
600
35
SMC
SMA
On Semiconductor
www.onsemi.com
MURS360
MURA260
MURA160
3
2
1
600
75
SMC
SMA
Vishay
www.vishay.com
USB260
US1G
US1M
GURB5H60
2
1
5
600
400
1000
600
30
50
75
30
SMB
SMA
D2PAK
I
AVG =
I
PK VTRANS
2 (V
OUT + N VTRANS )
The highest average diode current occurs at low output
voltages and decreases as the output voltage increases.
Reverse recovery time, reverse bias leakage and junction
capacitance should also be considered. All affect the overall
charging efciency. Excessive diode reverse recovery
times can cause appreciable discharging of the output
capacitor, thereby increasing charge time. Choose a diode
with a reverse recovery time of less than 100ns. Diode
leakage current under high reverse bias bleeds the output
capacitor of charge and increases charge time. Choose a
diode that has minimal reverse bias leakage current. Diode
junction capacitance is reected back to the primary, and
energy is lost during the NMOS intrinsic diode conduction.
Choose a diode with minimal junction capacitance. Table 4
recommends several output diodes for various output
voltages that have adequate reverse recovery times.
Setting Current Limit
Placing a sense resistor from the positive sense pin, CSP,
to the negative sense pin, CSN, sets the maximum peak
switch current. The maximum current limit is nominally
106mV/RSENSE. The power rating of the current sense
resistor must exceed:
P
RSENSE ≥
I
2
PK RSENSE
3
V
OUT(PK)
V
OUT(PK) + N VTRANS
Additionally, there is approximately a 180ns propaga-
tion delay from the time that peak current limit is
相关PDF资料 |
PDF描述 |
|---|---|
| LT3751EFE | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| LT3751EUFD#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
| LT3751EUFD | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
| LT3751IFE#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| LT3782AEFE#TR | SWITCHING CONTROLLER, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3754 | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel 50mA LED |
| LT3754EUH#PBF | 功能描述:IC LED DRIVER AUTOMOTIVE 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3754EUH#TRPBF | 功能描述:IC LED DVR 16CH 50MA 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3754EUHPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel × 50mA LED Driver |
| LT3754EUHTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel × 50mA LED Driver |
发布紧急采购，3分钟左右您将得到回复。