- 您现在的位置：买卖IC网 > PDF目录30768 > LT3751IUFD#TRPBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 PDF资料下载
参数资料
| 型号： | LT3751IUFD#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
| 封装： | 4 X 5 MM, LEAD FREE, PLASTIC, QFN-20 |
| 文件页数： | 13/34页 |
| 文件大小： | 403K |
| 代理商： | LT3751IUFD#TRPBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LT3751
20
3751fb
APPLICATIONS INFORMATION
detected to when the gate transitions to the low state.
This delay increases the peak current limit by
(VTRANS)(180ns)/LPRI.
Sense resistor inductance (LRSENSE) is another source of
current limit error. LRSENSE creates an input offset voltage
(VOS) to the current comparator and causes the current
comparator to trip early. VOS can be calculated as:
V
OS = VTRANS
L
RSENSE
L
PRIMARY
The change in current limit becomes VOS/RSENSE.Theerror
is more signicant for applications using large di/dt ratios
in the transformer primary. It is recommended to use very
low inductance (< 2nH) sense resistors. Several resistors
can be placed in parallel to help reduce the inductance.
Care should also be taken in placement of the sense lines. The
negative return line, CSN, must be a dedicated trace to the low
sideresistorterminal.HaphazardlyroutingtheCSNconnection
to the ground plane can cause inaccurate current limit.
DONE and FAULT Pin Design
Both the DONE and FAULT pins require proper pull-up
resistors or current sources. Limit pin current to 1mA
into either of these pins. 100kΩ pull-up resistors are
recommended for most applications. Both the DONE and
FAULT pins are latched in the low output state. Resetting
either latch requires the CHARGE pin to be toggled. A
fault condition will also cause the DONE pin to go low.
A third, non-latching condition occurs during startup
when the CHARGE pin is driven high. During this start-up
condition, both the DONE and FAULT pins will go low for
several micro seconds. This indicates the internal rails
are still ramping to their proper levels. External RC lters
may be added to both indication pins to remove start-up
indication. Time constants for the RC lter should be
between 5μs to 20μs.
Under/Overvoltage Lockout
The LT3751 provides user-programmable under and
overvoltage lockouts for both VCC and VTRANS. Use the
equations in the Pin Functions section for proper selection
of resistor values. When under/overvoltage lockout
comparators are tripped, the master latch is disabled, power
delivery is halted, and the FAULT pin goes low. Adequate
supply bulk capacitors should be used to reduce power
supply voltage ripple that could cause false tripping during
normal switching operation.
The LT3751 provides internal Zener clamping diodes to
protect itself in shutdown when VTRANS is operated above
55V. Supply voltages should only be applied to UVLO1,
UVLO2, OVLO1 and OVLO2 with series resistance such
that the Absolute Maximum pin currents are not exceeded.
Pin current can be calculated using:
I
PIN =
V
APPLIED 55V
R
SERIES
Note that in shutdown, RVTRANS, RVOUT, RDCM, UVLO1,
UVLO2, OVLO1 and OVLO2 currents increase signicantly
when operating VTRANS above the Zener clamp voltages
and are inversely proportional to the external series pin
resistances.
NMOS Snubber Design
The transformer leakage inductance causes a parasitic
voltage spike on the drain of the power NMOS switch during
the turn-off transition. Transformer leakage inductance
effects become more apparent at high peak primary
currents. The worst-case magnitude of the voltage spike is
determined by the energy stored in the leakage inductance
and the total capacitance on the VDRAIN node.
V
D,LEAK =
L
LEAK I
2
PK
C
VDRAIN
相关PDF资料 |
PDF描述 |
|---|---|
| LT3751EFE | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| LT3751EUFD#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
| LT3751EUFD | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
| LT3751IFE#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| LT3782AEFE#TR | SWITCHING CONTROLLER, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3754 | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel 50mA LED |
| LT3754EUH#PBF | 功能描述:IC LED DRIVER AUTOMOTIVE 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3754EUH#TRPBF | 功能描述:IC LED DVR 16CH 50MA 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3754EUHPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel × 50mA LED Driver |
| LT3754EUHTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel × 50mA LED Driver |
发布紧急采购，3分钟左右您将得到回复。