- 您现在的位置：买卖IC网 > PDF目录30768 > LT3751IUFD#TRPBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 PDF资料下载
参数资料
| 型号： | LT3751IUFD#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
| 封装： | 4 X 5 MM, LEAD FREE, PLASTIC, QFN-20 |
| 文件页数： | 4/34页 |
| 文件大小： | 403K |
| 代理商： | LT3751IUFD#TRPBF |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LT3751
12
3751fb
OPERATION
At very low output voltages, the boundary-mode switching
cycle period increases signicantly such that the energy
stored in the transformer core is not depleted before the
next clock cycle. In this situation, the clock may initiate
another switching cycle before the secondary winding
current reaches zero and cause the LT3751 to enter con-
tinuous-mode conduction. Normally, this is not a problem;
however, if the secondary energy transfer time is much
longer than the CLK period, signicant primary current
overshoot can occur. This is due to the non-zero starting
point of the primary current when the switch turns on and
the nite speed of the current comparator.
The LT3751 startup circuitry adds an auxiliary current
comparator with a trip level 50% higher than the nominal
trip level. Every time the auxiliary current comparator
trips, the required clock count between switching cycles is
incremented by one. This allows more time for secondary
energy transfer.
Counter 1 in Figure 3 is set to its maximum count when
the rst DCM comparator one-shot is generated. If no
DCM one-shot is initiated in normal boundary-mode
operation during a maximum count of approximately
500μs, the LT3751 re-enters start-up mode and the count
is returned to zero.
Note that Counter 1 is initialized to zero at start-up. Thus,
the output of the startup circuitry will go high after one clock
cycle. Counter 2 is reset when the gate driver goes high.
This repeats until either the auxiliary current comparator
increments the required clock count or until VDRAIN is high
enough to sustain normal operation described in steps 2
through 4 in the previous section.
Entering Normal Boundary Mode
The LT3751 has two DCM comparator thresholds that are
dependent on what mode the part is in, either start-up
mode or normal boundary-mode, and the state of the mode
latch. For boundary-mode switching, the LT3751 requires
the DCM sense voltage (VDRAIN) to exceed VTRANS by the
ΔDCM comparator threshold, ΔVDRAIN:
ΔVDRAIN = (40μA + IOFFSET) RDCM – 40μA RVTRANS
where IOFFSET is mode dependent. The DCM one-shot
signal is negative edge triggered by the switch node,
VDRAIN, and indicates that the energy in the secondary
winding has depleted. For this to happen, VDRAIN must
exceed VTRANS + ΔVDRAIN prior to its negative edge; oth-
erwise, the DCM comparator will not generate a one-shot
to initiate the next switching cycle. The part would remain
stuck in this state indenitely; however, the LT3751 uses
the start-up protection circuitry to jumpstart switching if
the DCM comparator does not generate a one-shot after
a maximum time-out of 500μs.
Figure 4 shows a typical VDRAIN node waveform with
a test circuit voltage clamp applied to the output. VTH1
is the start-up threshold and is set internally by forcing
IOFFSET to 40μA. Once the rst DCM one-shot is initiated,
the mode latch is set to boundary-mode. The mode latch
then sets the clock count to maximum (500μs) and lowers
the DCM comparator threshold to VTH2 (IOFFSET = 20μA).
This provides needed hysteresis between start-up mode
and boundary-mode operation.
LOW NOISE REGULATION
Low noise voltage regulation can be achieved by adding
a resistive divider from the output node to the LT3751 FB
pin. At start-up (FB pin below 1.16V), the LT3751 enters
the charge mode to rapidly charge the output capacitor.
Once the FB pin is within the threshold range of 1.16V
to 1.34V, the part enters into low noise regulation. The
switching methodology in regulation mimics that used
in the capacitor charging mode, but with the addition of
peak current and duty cycle control techniques. Figure 5
shows the steady state operation for both regulation
techniques. Figure 6 shows how both techniques are
combined to provide stable, low noise operation over a
wide load and supply range.
During heavy load conditions, the LT3751 sets the peak
primary current to its maximum value, 106mV/RSENSE and
sets the maximum duty cycle to approximately 95%. This
allows for maximum power delivery. At very light loads,
the opposite occurs, and the LT3751 reduces the peak
primary current to approximately one tenth its maximum
value while modulating the duty cycle below 10%. The
LT3751 controls moderate loads with a combination of
peak current mode control and duty cycle control.
相关PDF资料 |
PDF描述 |
|---|---|
| LT3751EFE | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| LT3751EUFD#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
| LT3751EUFD | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC20 |
| LT3751IFE#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| LT3782AEFE#TR | SWITCHING CONTROLLER, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3754 | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel 50mA LED |
| LT3754EUH#PBF | 功能描述:IC LED DRIVER AUTOMOTIVE 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3754EUH#TRPBF | 功能描述:IC LED DVR 16CH 50MA 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3754EUHPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel × 50mA LED Driver |
| LT3754EUHTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel × 50mA LED Driver |
发布紧急采购，3分钟左右您将得到回复。