- 您现在的位置：买卖IC网 > PDF目录1829 > LTC3425EUH#TRPBF (Linear Technology)IC REG BOOST SYNC ADJ 5A 32QFN PDF资料下载
参数资料
| 型号： | LTC3425EUH#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST SYNC ADJ 5A 32QFN |
| 标准包装： | 2,500 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2.4 V ~ 5.25 V |
| 输入电压： | 0.5 V ~ 4.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 100kHz ~ 2MHz |
| 电流 - 输出： | 5A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
LTC3425
OPERATIO
a heavy load is suddenly applied to the converter after
being in Burst Mode operation for an extended period of
time.
For automatic operation, an RC network should be con-
nected from BURST to ground. The value of the resistor
will control the average load current (I BURST ) at which
Burst Mode operation will be entered and exited (there is
hysteresis to prevent oscillation between modes). The
equation given for the capacitor on BURST is for the
minimum value, to prevent ripple on BURST from causing
the part to oscillate in and out of Burst Mode operation at
the current where the mode transition occurs.
to sink up to 2mA. Note that Burst Mode operation is
inhibited during start-up and soft-start.
Note that if V IN is raised to within 200mV or less below
V OUT , the part will exit Burst Mode operation and the
synchronous rectifier will be disabled. It will remain in
fixed frequency mode until V IN is at least 300mV below
V OUT .
If the load applied during forced Burst Mode operation
(BURST = GND) exceeds the current that can be supplied,
the output voltage will start to droop and the part will
automatically come out of Burst Mode operation and enter
fixed frequency mode, raising V OUT . The part will then
I BURST =
I BURST =
2 . 75
R BURST
1 . 7
R BURST
to leave Burst Mode operation
to enter Burst Mode operation
enter Burst Mode operation once again, the cycle will
repeat, resulting in about 4% output ripple. The maximum
current that can be supplied in Burst Mode operation is
given by:
2 ? ? 1 +
V OUT – V IN ?
?
?
where R BURST is in k? and I BURST is in Amps. For load
currents under 20mA, refer to the curve Automatic Burst
Mode Thresholds vs R BURST .
I O ( MAX ) =
?
?
0 . 60
V IN
in Amps
C BURST =
C OUT ? V OUT
10 , 000
Output Disconnect and Inrush Limiting
The LTC3425 is designed to allow true output disconnect
where C BURST(MIN) and C OUT are in μ F.
When the voltage on BURST drops below 0.94V, the part
will enter Burst Mode operation. When the BURST pin
voltage is above 1.06V, it will be in fixed frequency mode.
In the event that a sudden load transient causes the
feedback pin to drop by more than 4% from the regulation
value, an internal pull-up is applied to BURST, forcing the
part quickly out of Burst Mode operation. For optimum
transient response when going between Burst Mode
operation and PWM mode, the mode should be controlled
manually by the host. This way PWM mode can be
commanded before the load step occurs, minimizing
output voltage droop. For manual control of Burst Mode
operation, the RC network can be eliminated. To force
fixed frequency PWM mode, BURST should be connected
to V OUT . To force Burst Mode operation, BURST should be
grounded. The circuit connected to BURST should be able
by eliminating body diode conduction of the internal
PMOS rectifiers. This allows V OUT to go to zero volts
during shutdown, drawing no current from the input
source. It also allows for inrush current limiting at turn-on,
minimizing surge currents seen by the input supply. Note
that to obtain the advantages of output disconnect, there
cannot be any external Schottky diodes connected be-
tween the switch pins and V OUT .
Note: Board layout is extremely critical to minimize
voltage overshoot on the switch pins due to stray induc-
tance. Keep the output filter capacitors as close as
possible to the V OUT pins, and use very low ESR/ESL
ceramic capacitors tied to a good ground plane.
For applications with V OUT over 4.3V, Schottky diodes are
required to limit the peak switch voltage to less than 6V.
These must also be very close to minimize stray induc-
tance. See the section Applications Where V OUT > 4.3V.
3425f
16
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3426ES6#TRPBF | IC REG BOOST ADJ 2A TSOT23-6 |
| LTC3427EDC#TRPBF | IC REG BOOST SYNC ADJ 0.5A 6DFN |
| LTC3428EDD#TRPBF | IC REG BOOST ADJ 4A 10DFN |
| LTC3429ES6#TRM | IC REG BST SYNC ADJ .6A TSOT23-6 |
| LTC3440EDD#TRPBF | IC REG BUCK BOOST SYNC ADJ 10DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3426 | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.2MHz Step-Up DC/DC Converter in SOT-23 |
| LTC3426ES6 | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Up 1.6V to 4.3V 6-Pin TSOT-23 |
| LTC3426ES6#PBF | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Up 1.6V to 4.3V 6-Pin TSOT-23 |
| LTC3426ES6#TRM | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Up 1.6V to 4.3V 6-Pin TSOT-23 T/R |
| LTC3426ES6#TRMPBF | 功能描述:IC REG BOOST ADJ 2A TSOT23-6 RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:High Efficiency Current Mode Switching Regulators CMOS LDO Regulators 特色产品:BD91x Series Step-Down Regulators 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:2 输出电压:3.3V，0.8 V ~ 2.5 V 输入电压:4.5 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:1MHz 电流 - 输出:1.5A 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 包装:带卷 (TR) 供应商设备封装:VQFN020V4040 产品目录页面:1373 (CN2011-ZH PDF) 其它名称:BD9152MUV-E2TR |
发布紧急采购，3分钟左右您将得到回复。