- 您现在的位置：买卖IC网 > PDF目录1829 > LTC3447EDD#TRPBF (Linear Technology)IC REG BUCK SYNC ADJ 0.6A 10DFN PDF资料下载
参数资料
| 型号： | LTC3447EDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 0.6A 10DFN |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 0.69 V ~ 2.05 V |
| 输入电压： | 2.5 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 600mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-DFN（3x3） |
LTC3447
APPLICATIO S I FOR ATIO
loss dominates the ef?ciency loss at medium to high
load currents. In a typical ef?ciency plot, the ef?ciency
curve at very low load currents can be misleading since
the actual power lost is of no consequence as illustrated
in Figure 8.
1
0.1
0.01
R L and multiply the result by the square of the average
output current.
Other losses including C IN and C OUT ESR dissipative losses
and inductor core losses generally account for less than
2% total additional loss.
Checking Transient Response
The regulator loop response can be checked by looking
at the load transient response. Switching regulators take
several cycles to respond to a step in load current. When
a load step occurs, V OUT immediately shifts by an amount
equal to ( Δ I LOAD ? ESR), where ESR is the effective series
DAC = MAX
DAC = MIN
resistance of C OUT . Δ I LOAD also begins to charge or dis-
charge C OUT , which generates a feedback error signal.
0.001
0.1
1
10 100
LOAD CURRENT (mA)
1000
3447 F08
The regulator loop then acts to return V OUT to its steady
state value. During this recovery time V OUT can be moni-
Figure 8. Power Loss vs Load Current
The V IN quiescent current is due to two components: the
DC bias current as given in the electrical characteristics
and the internal main switch and synchronous switch
gate charge currents. The gate charge current results
from switching the gate capacitance of the internal power
MOSFET switches. Each time the gate is switched from
high to low to high again, a packet of charge, dQ, moves
from V IN to ground. The resulting dQ/dt is the current out
of V IN that is typically larger than the DC bias current. In
continuous mode, I GATECHG = f(QT + QB) where QT and
QB are the gate charges of the internal top and bottom
switches. Both the DC bias and gate charge losses are
proportional to V IN and thus their effects will be more
pronounced at higher supply voltages.
I 2 R losses are calculated from the resistances of the internal
switches, R SW , and external inductor R L . In continuous
mode, the average output current ?owing through inductor
L is “chopped” between the main switch and the synchro-
nous switch. Thus, the series resistance looking into the
SW pin is a function of both top and bottom MOSFET
R DS(ON) and the duty cycle (DC) as follows:
R SW = (R DS(ON)TOP )(DC) + (R DS(ON)BOT )(1 – DC)
The R DS(ON) for both the top and bottom MOSFETs can
be obtained from the Typical Performance Characteristics
curves. Thus, to obtain I 2 R losses, simply add R SW to
tored for overshoot or ringing that would indicate a stability
problem. For a detailed explanation of switching control
loop theory, see Application Note 76.
A second, more severe transient is caused by switching
in loads with large (>1μF) supply bypass capacitors. The
discharged bypass capacitors are effectively put in paral-
lel with C OUT , causing a rapid drop in V OUT . No regulator
can deliver enough current to prevent this problem if the
load switch resistance is low and it is driven quickly. The
only solution is to limit the rise time of the switch drive
so that the load rise time is limited to approximately (25
? C LOAD ). Thus, a 10μF capacitor charging to 3.3V would
require a 250μs rise time, limiting the charging current
to about 130mA.
Thermal Considerations
In most applications the LTC3447 does not dissipate much
heat due to its high ef?ciency. But, in applications where the
LTC3447 is running at high ambient temperature with low
supply voltage and high duty cycles, such as in dropout,
the heat dissipated may exceed the maximum junction
temperature of the part. If the junction temperature reaches
approximately 150°C, both power switches will be turned
off and the SW node will become high impedance.
To avoid the LTC3447 from exceeding the maximum junc-
tion temperature, the user will need to do some thermal
analysis. The goal of the thermal analysis is to determine
whether the power dissipated exceeds the maximum
3447f
13
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3448EMS8E#TRPBF | IC REG BUCK SYNC ADJ 0.6A 8MSOP |
| LTC3450EUD#TRPBF | IC CONV PS TRIPLE TFT/LCD 16QFN |
| LTC3458EDE#TRPBF | IC REG BOOST SYNC ADJ 1.4A 12DFN |
| LTC3459EDCB#TRPBF | IC REG BOOST SYNC ADJ 6DFN |
| LTC3499BEDD#TRPBF | IC REG BOOST SYNC ADJ 0.75A 8DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3448 | 制造商:LINER 制造商全称:Linear Technology 功能描述:1.5MHz/2.25MHz, 600mA Synchronous Step-Down Regulator with LDO Mode |
| LTC3448EDD | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:MIC23xxx HyperLight Load™ Regulators 标准包装:5,000 系列:HyperLight Load® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.8V 输入电压:2.7 V ~ 5.5 V PWM 型:混合物 频率 - 开关:4MHz 电流 - 输出:2A 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 包装:带卷 (TR) 供应商设备封装:8-MLF?（2x2） 产品目录页面:1094 (CN2011-ZH PDF) 其它名称:576-3303-2 |
| LTC3448EDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3448EDD#TRPBF | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
| LTC3448EMS8E | 功能描述:IC REG BUCK SYNC ADJ 0.6A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:升压（升压） 输出类型:可调式 输出数:1 输出电压:1.24 V ~ 30 V 输入电压:1.5 V ~ 12 V PWM 型:电流模式，混合 频率 - 开关:600kHz 电流 - 输出:500mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) 供应商设备封装:8-SOIC |
发布紧急采购，3分钟左右您将得到回复。