- 您现在的位置：买卖IC网 > PDF目录80057 > LTC3589IUJ-1#PBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 PDF资料下载
参数资料
| 型号： | LTC3589IUJ-1#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封装： | 6 X 6 MM, 0.75 MM HEIGHT, LEAD FREE, PLASTIC, QFN-40 |
| 文件页数： | 18/46页 |
| 文件大小： | 570K |
| 代理商： | LTC3589IUJ-1#PBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
LTC3589/LTC3589-1
25
3589fc
Operating Modes
Table 10 shows the I2C command registers used to control
theoperatingmodesoftheLTC3589/LTC3589-1buck-boost
converter. When command register SCR1 bit 6 is LOW,
the LTC3589 buck-boost switching regulator operates in
a xed frequency pulse width modulation mode using
voltage mode feedback control. A proprietary switching
algorithm allows the converter to transition between buck,
buck-boost, and boost modes without discontinuity in in-
ductor current or loop characteristics. The switch topology
is shown in the application circuit in Figure 4.
When the input voltage is significantly greater than the
output voltage, the buck-boost converter operates in
buck mode. Switch D turns on continuously and switch C
remains off. Switches A and B are pulse width modulated
to produce the required duty cycle to support the output
regulation voltage. As the input voltage decreases, switch A
remains on for a larger portion of the switching cycle.
When the duty cycle reaches approximately 85%, the
switch pair AC begins turning on for a small fraction of the
switching period. As the input voltage decreases further,
the AC switch pair remains on for longer durations and
the duration of the BD phase decreases proportionately.
As the input voltage drops below the output voltage, the
AC phase will eventually increase to the point that there is
no longer any BD phase. At this point, switch A remains
on continuously while switches CD operate as a boost
converter to regulate the desired output voltage.
The buck-boost is set to Burst Mode operation by writing
a 1 to command register SCR1 bit 6. Using Burst Mode
operation at light loads improves efficiency and reduces
standby current at zero loads. In Burst Mode operation,
the inductor is charged with bursts of fixed peak amplitude
current pulses. The current pulses are repeated as often
as necessary to maintain the target output voltage. The
maximum output current that can be supplied in Burst Mode
operation is dependent upon the input and output voltage.
Typically IOUT(MAX) in Burst Mode operation is equal to:
IOUT(MAX) =
0.28 VIN
VOUT+ VIN
(A)
If the buck-boost load exceeds the maximum Burst Mode
current capability then the output rail will lose regula-
tion and the power good comparator will indicate a fault
condition.
When the LTC3589/LTC3589-1 buck-boost is not enabled,
a 2.5k pull-down resistor is connected between BB_OUT
and ground.
Soft-Start
The buck-boost converter has an internal voltage mode soft-
start circuit that ramps the buck-boosts error amp reference
from 0V to 800mV at a rate of 2V/ms. During soft-start,
the converter is regulating to the ramping reference and
will respond to output load transients. During soft-start the
buck-boost converter is forced into continuous mode opera-
tion regardless of the state of the SCR1 command register.
Current Limit Operation
The LTC3589/LTC3589-1 buck-boost regulator has current
limit circuits to limit forward current through the A switch
and reverse current through the D switch. The primary
forward current limit circuit injects a small fraction of
the inductor current into the feedback node whenever
the inductor current exceeds 2.7A (typical). Forcing the
current into the feedback node in the high gain feedback
circuit has the effect of lowering the output voltage until
the average current in switch A is equal to the current limit.
The average limit uses the error amplifier in its active linear
state so once the fault condition is removed the recovery
is smooth with little overshoot.
A hard short on the output of the buck-boost will cause the
inductor current to exceed the 2.7A average current limit.
A second current limit turns off switch A in the event peak
inductor current reaches 3A (typical). The instantaneous
forward current limit provides extra protection in the event
of a sudden hard short.
The reverse current comparator on the D switch moni-
tors the current entering the BB_OUT pin. When this
current exceeds 1A (typical) switch D will turn off for the
remainder of the switching cycle. This feature protects
the buck-boost converter from excessive reverse current
if the buck-boost output is held above the regulation point
by an external source.
OPERATION
相关PDF资料 |
PDF描述 |
|---|---|
| LES015YJ38N | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES015ZH38N | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LM2320-7ERV2F | 2-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
| LM2320-9ERD3A | 2-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
| LM2540-7ERD0AH | 2-OUTPUT 50 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3589IUJ-2#PBF | 功能描述:IC POWER MANAGEMENT RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:* 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3589IUJ-2#TRPBF | 功能描述:IC POWER MANAGEMENT RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:* 标准包装:1 系列:- 应用:手持/移动设备 电流 - 电源:- 电源电压:3 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-WFDFN 裸露焊盘 供应商设备封装:14-LLP-EP（4x4） 包装:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名称:LP3905SD-30DKR |
| LTC3589IUJ-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:8-Output Regulator with Sequencing and I2C |
| LTC3589IUJ-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:8-Output Regulator with Sequencing and I2C |
| LTC3600EDD#PBF | 功能描述:IC REG BUCK SYNC ADJ 1.5A 12DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
发布紧急采购，3分钟左右您将得到回复。