- 您现在的位置：买卖IC网 > PDF目录15270 > LTC3709EUH#TRPBF (Linear Technology)IC REG CTRLR BUCK PWM CM 32-QFN PDF资料下载
参数资料
| 型号： | LTC3709EUH#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/24页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 32-QFN |
| 标准包装： | 2,500 |
| 系列： | PolyPhase® |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 200kHz |
| 占空比： | 90% |
| 电源电压： | 5 V ~ 36 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
LTC3709
APPLICATIO S I FOR ATIO
The selection of C OUT is primarily determined by the ESR
required to minimize voltage ripple and load step transients.
The output ripple ? V OUT is approximately bounded by:
Discontinuous Mode Operation and FCB Pin
The FCB pin determines whether the bottom MOSFET
remains on when current reverses in the inductor. Tying
? V OUT L ? ESR +
8 fC OUT ?
≤ ? I
?
?
1 ?
?
this pin to V CC enables discontinuous operation where the
bottom MOSFET turns off when inductor current reverses.
The load current at which inductor current reverses and
Since ? I L increases with input voltage, the output ripple is
highest at maximum input voltage. Typically, once the ESR
requirement is satisfied, the capacitance is adequate for
filtering and has the necessary RMS current rating.
Multiple capacitors placed in parallel may be needed to
meet the ESR and RMS current handling requirements.
Dry tantalum, special polymer, aluminum electrolytic and
ceramic capacitors are all available in surface mount
packages. Special polymer capacitors offer very low ESR
but have lower capacitance density than other types.
Tantalum capacitors have the highest capacitance density
but it is important to only use types that have been surge
tested for use in switching power supplies. Aluminum
electrolytic capacitors have significantly higher ESR, but
can be used in cost-sensitive applications providing that
consideration is given to ripple current ratings and long-
term reliability. Ceramic capacitors have excellent low
ESR characteristics but can have a high voltage coefficient
and audible piezoelectric effects. High performance
through-hole capacitors may also be used, but an addi-
tional ceramic capacitor in parallel is recommended to
reduce the effect of their lead inductance.
Top MOSFET Driver Supply (C B , D B )
discontinuous operation begins depends on the amplitude
of the inductor ripple current. The ripple current depends
on the choice of inductor value and operating frequency as
well as the input and output voltages.
Tying the FCB pin to ground forces continuous synchro-
nous operation, allowing current to reverse at light loads
and maintaining high frequency operation.
Besides providing a logic input to force continuous opera-
tion, the FCB pin acts as the input for external clock syn-
chronization. Upon detecting a TTL level clock and the fre-
quency is higher than the minimum allowable, channel 1
will lock on to this external clock. This will be followed by
channel 2 (see PLL and Frequency Synchronization). The
LTC3709 will be forced to operate in forced continuous
mode in this situation.
Fault Conditions: Current Limit
The maximum inductor current is inherently limited in a
current mode controller by the maximum sense voltage. In
the LTC3709, the maximum sense voltage is controlled by
the voltage on the V RNG pin. With valley current control,
the maximum sense voltage and the sense resistance
determine the maximum allowed inductor valley current.
The corresponding output current limit is:
? V SNS ( MAX )
I LIMIT = ?
AnexternalbootstrapcapacitorC B connectedtotheBOOST
pin supplies the gate drive voltage for the topside MOSFET.
This capacitor is charged through diode D B from DRV CC
when the switch node is low. Note that the average voltage
? R DS ( ON ) ? ρ T
+
1
2
?
? ? I L ? ? 2
?
across C B is approximately DRV CC . When the top MOSFET
turns on, the switch node rises to V IN and the BOOST pin
rises to approximately V IN + DRV CC . The boost capacitor
needs to store about 100 times the gate charge required by
the top MOSFET. In most applications 0.1 μ F to 0.47 μ F is
adequate.
The current limit value should be checked to ensure that
I LIMIT(MIN) > I OUT(MAX) . The minimum value of current limit
generally occurs with the largest V IN at the highest ambi-
ent temperature, conditions which cause the largest power
loss in the converter. Note that it is important to check for
3709fb
15
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3829IUHF#TRPBF | IC REG CTRLR BUCK PWM CM 38-QFN |
| LTC1266ACS#TRPBF | IC REG CTRLR BST PWM CM 16-SOIC |
| LTC1266ACS#TR | IC REG CTRLR BST PWM CM 16-SOIC |
| LTC1625CGN#TRPBF | IC REG CTRLR BUCK PWM CM 16-SSOP |
| LTC1625CGN#TR | IC REG CTRLR BUCK PWM CM 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC-3710 | 制造商:LITEON 制造商全称:Lite-On Technology Corporation 功能描述:0.3 FOUR LED CLOCK FREQUENCY DISPLAYS |
| LTC-3710E | 制造商:LITEON 制造商全称:Lite-On Technology Corporation 功能描述:0.3 FOUR LED CLOCK FREQUENCY DISPLAYS |
| LTC-3710G | 功能描述:LED 显示器和配件 4 Digit, Green RoHS:否 制造商:Avago Technologies 显示器类型:7 Segment 数位数量:2 字符大小:7.8 mm x 14.22 mm 照明颜色:Red 波长:628 nm 共用管脚:Common Anode 工作电压:2.05 V 工作电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 35 C 封装:Tube |
| LTC-3710HR | 功能描述:LED 显示器和配件 4 Digit, Red RoHS:否 制造商:Avago Technologies 显示器类型:7 Segment 数位数量:2 字符大小:7.8 mm x 14.22 mm 照明颜色:Red 波长:628 nm 共用管脚:Common Anode 工作电压:2.05 V 工作电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 35 C 封装:Tube |
| LTC-3710P | 功能描述:LED 显示器和配件 4 Digit, Red RoHS:否 制造商:Avago Technologies 显示器类型:7 Segment 数位数量:2 字符大小:7.8 mm x 14.22 mm 照明颜色:Red 波长:628 nm 共用管脚:Common Anode 工作电压:2.05 V 工作电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 35 C 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。