- 您现在的位置：买卖IC网 > PDF目录15270 > LTC3709EUH#TRPBF (Linear Technology)IC REG CTRLR BUCK PWM CM 32-QFN PDF资料下载
参数资料
| 型号： | LTC3709EUH#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 20/24页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 32-QFN |
| 标准包装： | 2,500 |
| 系列： | PolyPhase® |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 200kHz |
| 占空比： | 90% |
| 电源电压： | 5 V ~ 36 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
LTC3709
APPLICATIO S I FOR ATIO
PC Board Layout Checklist
When laying out a PC board follow one of the two sug-
gested approaches. The simple PC board layout requires
a dedicated ground plane layer. Also, for higher currents,
it is recommended to use a multilayer board to help with
heat sinking power components.
? The ground plane layer should not have any traces and
it should be as close as possible to the layer with power
MOSFETs.
? Place C IN , C OUT , MOSFETs, D1, D2 and inductors all in
one compact area. It may help to have some compo-
nents on the bottom side of the board.
? Use an immediate via to connect the components to
ground plane including SGND and PGND of LTC3709.
Use several larger vias for power components.
? Use a compact plane for switch node (SW) to keep EMI
down.
? Use planes for V IN and V OUT to maintain good voltage
filtering and to keep power losses low.
? Flood all unused areas on all layers with copper. Flood-
ing with copper will reduce the temperature rise of
power component. You can connect the copper areas to
any DC net (V IN , V OUT , GND or to any other DC rail in
your system).
When laying out a printed circuit board, without a ground
plane, use the following checklist to ensure proper opera-
tion of the controller. These items are also illustrated in
Figure 9.
? Segregate the signal and power grounds. All small
signal components should return to the SGND pin at
one point, which is then tied to a “clean” point in the
power ground such as the “–” node of C IN .
? Minimize impedance between input ground and output
ground.
? Connect PGND1 to the source of M2 or R S1 (QFN)
directly. This also applies to channel 2.
? Place M2 as close to the controller as possible, keeping
the PGND1, BG1 and SW1 traces short. The same for
the other channel. SW2 trace should connect to the
drain of M2 directly.
? Connect the input capacitor(s) C IN close to the power
MOSFETs: (+) node to drain of M1, (–) node to source
of M2. This capacitor carries the MOSFET AC current.
? Keep the high dV/dt SW, BOOST and TG nodes away
from sensitive small-signal nodes.
? Connect the DRV CC decoupling capacitor C VCC closely
to the DRV CC and PGND pins.
? Connect the top driver boost capacitor C B closely to the
BOOST and SW pins.
? Connect the V IN pin decoupling capacitor C F closely to
the V CC and PGND pins.
? Are the SENSE – and SENSE + leads routed together with
minimum PC trace spacing? The filter capacitor be-
tween SENSE – and SENSE + (C SENSE ) should be as close
as possible to the IC. Ensure accurate current sensing
with Kelvin connections at the sense resistor as shown
in Figure 8.
D
D
D
D
G
S
S
S
MOSFET
R SENSE
SENSE + SENSE –
(8a) Sensing the Bottom MOSFET
SENSE + SENSE –
(8b) Sensing a Resistor
3709 F08
Figure 8. Kelvin Sensing
3709fb
20
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3829IUHF#TRPBF | IC REG CTRLR BUCK PWM CM 38-QFN |
| LTC1266ACS#TRPBF | IC REG CTRLR BST PWM CM 16-SOIC |
| LTC1266ACS#TR | IC REG CTRLR BST PWM CM 16-SOIC |
| LTC1625CGN#TRPBF | IC REG CTRLR BUCK PWM CM 16-SSOP |
| LTC1625CGN#TR | IC REG CTRLR BUCK PWM CM 16-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC-3710 | 制造商:LITEON 制造商全称:Lite-On Technology Corporation 功能描述:0.3 FOUR LED CLOCK FREQUENCY DISPLAYS |
| LTC-3710E | 制造商:LITEON 制造商全称:Lite-On Technology Corporation 功能描述:0.3 FOUR LED CLOCK FREQUENCY DISPLAYS |
| LTC-3710G | 功能描述:LED 显示器和配件 4 Digit, Green RoHS:否 制造商:Avago Technologies 显示器类型:7 Segment 数位数量:2 字符大小:7.8 mm x 14.22 mm 照明颜色:Red 波长:628 nm 共用管脚:Common Anode 工作电压:2.05 V 工作电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 35 C 封装:Tube |
| LTC-3710HR | 功能描述:LED 显示器和配件 4 Digit, Red RoHS:否 制造商:Avago Technologies 显示器类型:7 Segment 数位数量:2 字符大小:7.8 mm x 14.22 mm 照明颜色:Red 波长:628 nm 共用管脚:Common Anode 工作电压:2.05 V 工作电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 35 C 封装:Tube |
| LTC-3710P | 功能描述:LED 显示器和配件 4 Digit, Red RoHS:否 制造商:Avago Technologies 显示器类型:7 Segment 数位数量:2 字符大小:7.8 mm x 14.22 mm 照明颜色:Red 波长:628 nm 共用管脚:Common Anode 工作电压:2.05 V 工作电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 35 C 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。