- 您现在的位置：买卖IC网 > PDF目录20858 > LTC3783IFE#PBF (Linear Technology)IC LED DRVR PWM CONTROL 16-TSSOP PDF资料下载
参数资料
| 型号： | LTC3783IFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 19/24页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR PWM CONTROL 16-TSSOP |
| 标准包装： | 95 |
| 恒定电流： | 是 |
| 恒定电压： | 是 |
| 拓扑： | 回扫，PWM，SEPIC，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 车载，通用 |
| 频率： | 20kHz ~ 1MHz |
| 电源电压： | 3 V ~ 36 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
LTC3783
OPERATION
V IN(MIN) 12V
? I L ? f
L = ? D MAX =
Andsotheinductorvalueis:
0.6A ? 1MHz
4. R SENSE should be:
? 0.53 = 11μH
8. The choice of an input capacitor for a boost converter
depends on the impedance of the source supply and the
amount of input ripple the converter will safely tolerate.
For this particular design and lab setup, 20μF was found
to be satisfactory.
R SENSE =
0.5 ? V SENSE(MAX) 0.5 ? 150mV
I IN(PEAK)
= = 42m ?
C OUT >
I OUT(MAX) 0.7A
0.01 ? V OUT ? f
= = 3 μ F
I RMS(COUT) = I OUT(MAX) ?
= 0.7A ?
= 0.7A
C SS(MIN) >
1.8A
5. The diode for this design must handle a maximum DC
output current of 0.7A and be rated for a minimum reverse
voltage of V OUT , or 25V. A 1A, 40V diode from Zetex was
chosen for its specifications, especially low leakage at
higher temperatures, which is important for maintaining
dimming range.
6. Voltage and value permitting, the output capacitor usu-
ally consists of some combination of low ESR ceramics.
Based on a maximum output ripple voltage of 1%, or
250mV, the bulk C needs to be greater than:
0.01 ? 25V ? 1MHz
The RMS ripple current rating for this capacitor needs
to exceed:
V OUT – V IN(MIN)
V IN(MIN)
25V – 12V
12V
Based on value and ripple current, and taking physical
size into account, a surface mount ceramic capacitor is a
good choice. A 4.7μF TDK C5750X7R1H475M will satisfy
all requirements in a compact package.
7. The soft-start capacitor should be:
2 ? dimming ratio ? 50 μ A ? C OUT ? V OUT ? R DS(ON)/SENSE
150mV ? 1.2V
PC Board Layout Checklist
1. In order to minimize switching noise and improve out-
put load regulation, the GND pad of the LTC3783 should
be connected directly to 1) the negative terminal of the
INTV CC decoupling capacitor, 2) the negative terminal of
the output decoupling capacitors, 3) the bottom terminals
of the sense resistors or the source of the power MOSFET,
4) the negative terminal of the input capacitor, and 5) at
least one via to the ground plane immediately under the
exposed pad. The ground trace on the top layer of the PC
board should be as wide and short as possible to minimize
series resistance and inductance.
2. Beware of ground loops in multiple layer PC boards. Try
to maintain one central ground node on the board and use
the input capacitor to avoid excess input ripple for high
output current power supplies. If the ground plane is to
be used for high DC currents, choose a path away from
the small-signal components.
3. Place the C VCC capacitor immediately adjacent to the
INTV CC and GND pins on the IC package. This capacitor
carries high di/dt MOSFET gate-drive currents. A low ESR
and ESL 4.7μF ceramic capacitor works well here.
4. The high di/dt loop from the bottom terminal of the output
capacitor, through the power MOSFET, through the boost
diode and back through the output capacitors should be
kept as tight as possible to reduce inductive ringing. Excess
inductance can cause increased stress on the power MOSFET
and increase HF noise on the output. If low ESR ceramic
capacitors are used on the output to reduce output noise,
place these capacitors close to the boost diode in order to
keep the series inductance to a minimum.
>
2 ? 3000 ? 50 μ A ? 4.7 μ F ? 25V ? 42m ?
150mV ? 1.2V
= 8 μ F
3783fb
19
相关PDF资料 |
PDF描述 |
|---|---|
| P51-300-G-S-I36-20MA-000-000 | SENSOR 300PSI 1/4-18NPT 4-20MA |
| P51-3000-S-F-I12-4.5V-000-000 | SENSOR 3000PSI 1/4-18NPT .5-4.5V |
| BAS16W-7 | DIODE SWITCH 75V 200MW SC70-3 |
| REC7.5-4815DRW/H2/A/M | CONV DC/DC 7.5W 36-72VIN +/-15V |
| P51-2000-S-S-MD-4.5V-000-000 | SENSOR 2000PSI 1/4-18NPT 4.5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3785EUF#PBF | 功能描述:IC REG CTRLR BST PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3785EUF#TRPBF | 功能描述:IC REG CTRLR BST PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3785EUF-1#PBF | 功能描述:IC REG CTRLR BST PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3785EUF-1#TRPBF | 功能描述:IC REG CTRLR BST PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3785EUFPBF | 制造商:Linear Technology 功能描述:10V Synch Buck-Boost Controller LTC3785 |
发布紧急采购，3分钟左右您将得到回复。