- 您现在的位置：买卖IC网 > PDF目录20858 > LTC3783IFE#PBF (Linear Technology)IC LED DRVR PWM CONTROL 16-TSSOP PDF资料下载
参数资料
| 型号： | LTC3783IFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 20/24页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR PWM CONTROL 16-TSSOP |
| 标准包装： | 95 |
| 恒定电流： | 是 |
| 恒定电压： | 是 |
| 拓扑： | 回扫，PWM，SEPIC，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 车载，通用 |
| 频率： | 20kHz ~ 1MHz |
| 电源电压： | 3 V ~ 36 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
LTC3783
OPERATION
5. Check the stress on the power MOSFET by measuring its
drain-to-source voltage directly across the device terminals
(reference the ground of a single scope probe directly to the
source pad on the PC board). Beware of inductive ringing
which can exceed the maximum specified voltage rating of
the MOSFET. If this ringing cannot be avoided and exceeds the
maximum rating of the device, either choose a higher voltage
device or specify an avalanche-rated power MOSFET.
6. Place the small-signal components away from high
frequency switching nodes. All of the small-signal com-
ponents should be placed on one side of the IC and all
of the power components should be placed on the other.
This also allows the use of a pseudo-Kelvin connection for
the signal ground, where high di/dt gate driver currents
flow out of the IC ground pad in one direction (to bottom
plate of the INTV CC decoupling capacitor) and small-signal
currents flow in the other direction.
7. If a sense resistor is used in the source of the power
MOSFET, minimize the capacitance between the SENSE
pin trace and any high frequency switching nodes. The
LTC3783 contains an internal leading-edge blanking time
of approximately 160ns, which should be adequate for
most applications.
8. For optimum load regulation and true remote sensing,
the top of the output resistor should connect indepen-
dently to the top of the output capacitor (Kelvin connec-
tion), staying away from any high dV/dt traces. Place the
divider resistors near the LTC3783 in order to keep the
high impedance FBN node short.
9. For applications with multiple switching power convert-
ers connected to the same input supply, make sure that
the input filter capacitor for the LTC3783 is not shared
with any other converters. AC input current from another
converter could cause substantial input voltage ripple, and
this could interfere with the operation of the LTC3783. A
few inches of PC trace or wire (L ~ 100nH) between the
C IN of the LTC3783 and the actual source V IN should be
sufficient to prevent current-sharing problems.
Returning the Load to V IN : A Single Inductor
Buck-Boost Application
As shown in Figure 11, due to its available high side current
sensing mode, the LTC3783 is also well-suited to a boost
converter in which the load current is returned to V IN ,
hence providing a load voltage (V OUT – V IN ) which can be
greater or less than the input voltage V IN . This configuration
allows for complete overlap of input and output voltages,
with the disadvantages that only the load current, and not
the load voltage, can be tightly regulated. The switch must
be rated for a V DS(MAX) equal to V IN + V LOAD .
The design of this circuit resembles that of the boost
converter above, and the procedure is much the same,
except V OUT is now (V IN + V LOAD ), and the duty cycles
and voltages must be adjusted accordingly.
1M
LTC3783
10μF, 50V
× 2
UMK432C106MM
10μH
SUMIDA
CDRH8D28-100
PMEG6010
V IN
R L 9V TO 26V
0.28
LED STRING 1-4 EA
LUMILEDS LHXL-BW02
EACH LED IS 3V TO 4.2V
AT 350mA
PWM
5V AT 0Hz TO 10Hz
1μF
4.7μF
100k
20k
RUN V IN
PWMIN OV/FB
I TH PWMOUT
SS I LIM
V REF GATE
FBP SENSE
FBN INTV CC
FREQ GND
SYNC
0V TO
1.23V
4.7μF
40.2k
FAIRCHILD
FDN5630
0.05
1k
V OUT
10μF, 50V
C5750X7R1H106M
CERAMIC
GND
3783 F11
Figure 11. Single Inductor Buck-Boost Application with Analog Dimming and Low Frequency PWM Dimming
3783fb
20
相关PDF资料 |
PDF描述 |
|---|---|
| P51-300-G-S-I36-20MA-000-000 | SENSOR 300PSI 1/4-18NPT 4-20MA |
| P51-3000-S-F-I12-4.5V-000-000 | SENSOR 3000PSI 1/4-18NPT .5-4.5V |
| BAS16W-7 | DIODE SWITCH 75V 200MW SC70-3 |
| REC7.5-4815DRW/H2/A/M | CONV DC/DC 7.5W 36-72VIN +/-15V |
| P51-2000-S-S-MD-4.5V-000-000 | SENSOR 2000PSI 1/4-18NPT 4.5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3785EUF#PBF | 功能描述:IC REG CTRLR BST PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3785EUF#TRPBF | 功能描述:IC REG CTRLR BST PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3785EUF-1#PBF | 功能描述:IC REG CTRLR BST PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3785EUF-1#TRPBF | 功能描述:IC REG CTRLR BST PWM VM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3785EUFPBF | 制造商:Linear Technology 功能描述:10V Synch Buck-Boost Controller LTC3785 |
发布紧急采购，3分钟左右您将得到回复。