- 您现在的位置：买卖IC网 > PDF目录15302 > LTC3856EUH#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 32WFQFN PDF资料下载
参数资料
| 型号： | LTC3856EUH#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/40页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 32WFQFN |
| 标准包装： | 73 |
| 系列： | PolyPhase® |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 850kHz |
| 占空比： | 94% |
| 电源电压： | 4.5 V ~ 38 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
LTC3856
APPLICATIONS INFORMATION
R SENSE ( EQUIV ) =
I ( MAX ) +
R D =
R 1 || R 2 =
R 1 || R 2 R 1 ? R D
1 ? R D
R D
sheet for information about parasitic inductance. In the
absence of data, measure the voltage drop directly across
the sense resistor to extract the magnitude of the ESL step
and use Equation 1 to determine the ESL. However, do not
overfilter. Keep the RC time constant, less than or equal
to the inductor time constant to maintain a high enough
ripple voltage of ? V SENSE . The equation generally applies
to high density/high current applications where I MAX >
10A and low values of inductors are used. For applications
where I MAX < 10A, set R F to 10Ω and C F to 1000pF. This
will provide a good starting point. The filter components
need to be placed close to the IC. The positive and nega-
tive sense traces need to be routed as a differential pair
and Kelvin connected to the sense resistor.
Inductor DCR Sensing
For applications requiring the highest possible efficiency
at high load currents, the LTC3856 is capable of sensing
the voltage drop across the inductor DCR, as shown in
Figure 2b. The DCR of the inductor represents the small
amount of DC winding resistance of the copper, which
can be less than 1mΩ for today’s low value, high current
inductors. In a high current application requiring such an
inductor, conduction loss through a sense resistor would
cost several points of efficiency compared to DCR sensing.
If the external R1|| R2 ? C1 time constant is chosen to be
exactly equal to the L/DCR time constant, the voltage drop
across the external capacitor is equal to the drop across
the inductor DCR multiplied by R2/(R1 + R2). R2 scales the
voltage across the sense terminals for applications where
the DCR is greater than the target sense resistor value.
To properly dimension the external filter components, the
DCR of the inductor must be known. It can be measured
using a good RLC meter, but the DCR tolerance is not
always the same and varies with temperature; consult the
manufacturers’ data sheets for detailed information.
Using the inductor ripple current value from the Inductor
Value Calculation and Output Ripple Current section, the
target sense resistor value is:
V SENSE(MAX )
? I L
2
To ensure that the application will deliver full load current
over the full operating temperature range, choose the
minimum value for the maximum current sense threshold
(V SENSE(MAX) ) in the Electrical Characteristics table (25mV,
45mV or 68mV, depending on the state of the I LIM pin).
Next, determine the DCR of the inductor. Where provided,
use the manufacturer’s maximum value, usually given at
20°C. Increase this value to account for the temperature
coefficient of resistance, which is approximately 0.4%/°C.
A conservative value for T L(MAX) is 100°C. To scale the
maximum inductor DCR to the desired sense resistor
value, use the divider ratio:
R SENSE ( EQUIV )
DCR MAX at T L ( MAX )
C1 is usually selected to be in the range of 0.047μF to
0.47μF. This forces R1|| R2 to around 2k, reducing error
that might have been caused by the SENSE + pins’ ±1μA
current. T L(MAX) is the maximum inductor temperature.
The equivalent resistance R1|| R2 is scaled to the room
temperature inductance and maximum DCR:
L
( DCR at 20 ° C ) ? C 1
The sense resistor values are:
R 1 = ; R 2 =
3856f
相关PDF资料 |
PDF描述 |
|---|---|
| EYM25DRSS | CONN EDGECARD 50POS DIP .156 SLD |
| VE-254-EW-F2 | CONVERTER MOD DC/DC 48V 100W |
| EGM25DRSS | CONN EDGECARD 50POS DIP .156 SLD |
| LTC3866EFE#TRPBF | IC REG CTRLR BUCK PWM CM 24TSSOP |
| EEM43DREF | CONN EDGECARD 86POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3856IFE#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 38TFSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3856IFE#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 38TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3856IUH#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 32WFQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3856IUH#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3857EGN-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
发布紧急采购，3分钟左右您将得到回复。