- 您现在的位置：买卖IC网 > PDF目录15302 > LTC3856EUH#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 32WFQFN PDF资料下载
参数资料
| 型号： | LTC3856EUH#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 28/40页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 32WFQFN |
| 标准包装： | 73 |
| 系列： | PolyPhase® |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 850kHz |
| 占空比： | 94% |
| 电源电压： | 4.5 V ~ 38 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
LTC3856
APPLICATIONS INFORMATION
short circuit). If more current is required through the
EXTV CC than is specified, an external Schottky diode can
be added between the EXTV CC and INTV CC pins. Do not
apply more than 6V to the EXTV CC pin and make sure that
EXTV CC < V IN .
Significant efficiency and thermal gains can be realized
by powering INTV CC from the output, since the V IN cur-
rent resulting from the driver and control currents will be
scaled by a factor of (duty cycle)/(switcher efficiency).
Tying the EXTV CC pin to a 5V supply reduces the junction
temperature in the previous example from 125°C to:
T J = 70°C + (42mA)(5V)(34°C/W) = 77°C
However, for low voltage outputs, additional circuitry is
required to derive INTV CC power from the output.
The following list summarizes the four possible connec-
tions for EXTV CC :
1. EXTV CC left open (or grounded). This will cause INTV CC
to be powered from the internal 5V LDO resulting
in an efficiency penalty of up to 10% at high input
voltages.
2. EXTV CC connected directly to V OUT . This is the normal
connection for a 5V regulator and provides the highest
efficiency.
3. EXTV CC connected to an external supply. If a 5V external
supply is available, it may be used to power EXTV CC
providing it is compatible with the MOSFET gate drive
requirements.
4. EXTV CC connected to an output-derived boost network.
For 3.3V and other low voltage regulators, efficiency
gains can still be realized by connecting EXTV CC to an
output-derived voltage that has been boosted to greater
than 4.7V.
For applications where the main input power is 5V, tie the
V IN and INTV CC pins together and tie the combined pins
to the 5V input with a 1Ω or 2.2Ω resistor (as shown in
Figure 13) to minimize the voltage drop caused by the
gate charge current. This will override the INTV CC linear
regulator and will prevent INTV CC from dropping too low
due to the dropout voltage. Make sure the INTV CC voltage
is at or exceeds the R DS(ON) test voltage for the MOSFET,
which is typically 4.5V for logic-level devices.
Topside MOSFET Driver Supply (C B , D B )
External bootstrap capacitors, C B , connected to the
BOOST pins supply the gate drive voltages for the top-
side MOSFETs. Capacitor C B in the Functional Diagram
is charged though external diode D B from INTV CC when
the SW pin is low. When one of the topside MOSFETs is
to be turned on, the driver places the C B voltage across
the gate source of the desired MOSFET. This enhances
the MOSFET and turns on the topside switch. The switch
node voltage, SW, rises to V IN and the BOOST pin follows.
With the topside MOSFET on, the boost voltage is above
the input supply:
V BOOST = V IN + V INTVCC
The value of the boost capacitor, C B , needs to be 100 times
that of the total input capacitance of the topside MOSFET(s).
The reverse breakdown of the external Schottky diode
must be greater than V IN(MAX) . When adjusting the gate
drive level, the final arbiter is the total input current for
the regulator. If a change is made and the input current
decreases, then the efficiency has improved. If there is
no change in input current, then there is no change in
efficiency.
V IN
LTC3856
INTV CC
C INTVCC
4.7 μ F
R VIN
1?
+
5V
C IN
3856 F13
Figure 13. Set-Up for a 5V Input
3856f
相关PDF资料 |
PDF描述 |
|---|---|
| EYM25DRSS | CONN EDGECARD 50POS DIP .156 SLD |
| VE-254-EW-F2 | CONVERTER MOD DC/DC 48V 100W |
| EGM25DRSS | CONN EDGECARD 50POS DIP .156 SLD |
| LTC3866EFE#TRPBF | IC REG CTRLR BUCK PWM CM 24TSSOP |
| EEM43DREF | CONN EDGECARD 86POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3856IFE#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 38TFSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3856IFE#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 38TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3856IUH#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 32WFQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3856IUH#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3857EGN-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
发布紧急采购，3分钟左右您将得到回复。