- 您现在的位置：买卖IC网 > PDF目录15302 > LTC3856EUH#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 32WFQFN PDF资料下载
参数资料
| 型号： | LTC3856EUH#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 35/40页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 32WFQFN |
| 标准包装： | 73 |
| 系列： | PolyPhase® |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 850kHz |
| 占空比： | 94% |
| 电源电压： | 4.5 V ~ 38 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页
LTC3856
APPLICATIONS INFORMATION
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the IC. These items are also illustrated graphically in the
layout diagram of Figure 17. Check the following in the
PC layout:
1. Are the signal and power ground paths Kelvin connected?
Keep the SGND at one end of a printed circuit path thus
preventing MOSFET currents from traveling under the
IC. The INTV CC decoupling capacitor should be placed
immediately adjacent to the IC between the INTV CC pin
and PGND plane. A 1μF ceramic capacitor of the X7R or
X5R type is small enough to fit very close to the IC to
minimize the ill effects of the large current pulses drawn
to drive the bottom MOSFETs. An additional 5μF to 10μF
of ceramic, tantalum or other very low ESR capacitance
is recommended in order to keep the internal IC supply
quiet. The power ground returns to the sources of the
bottom N-channel MOSFETs, anodes of the Schottky
diodes and (–) plates of C IN , which should have as short
lead lengths as possible.
2. Does the IC DIFFP pin connect to the (+) plates of
C OUT ? A 30pF to 300pF feedforward capacitor between
the DIFFP and V FB pins should be placed as close as
possible to the IC.
3. Are the SENSE – and SENSE + printed circuit traces for
each channel routed together with minimum PC trace
spacing? The filter capacitors between SENSE + and
SENSE – for each channel should be as close as possible
to the pins of the IC. Connect the SENSE – and SENSE +
pins to the pads of the sense resistor as illustrated in
Figure 1.
4. Do the (+) plates of C PWR connect to the drains of the
topside MOSFETs as closely as possible? This capacitor
provides the pulsed current to the MOSFETs.
5. Keep the switching nodes, SWn, BOOSTn and TGn away
from sensitive small-signal nodes (SENSE + , SENSE – ,
DIFFP, DIFFN, V FB , ITEMP). Ideally the SWn, BOOSTn
and TGn printed circuit traces should be routed away
and separated from the IC and especially the “quiet”
side of the IC. Separate the high dv/dt traces from sensi-
tive small-signal nodes with ground traces or ground
planes.
6. Use a low impedance source such as a logic gate to drive
the PLLIN pin and keep the lead as short as possible.
7. The 47pF to 330pF ceramic capacitor between the I TH
pin and signal ground should be placed as close as pos-
sible to the IC. Figure 17 illustrates all branch currents
in a 2-phase switching regulator. It becomes very clear
after studying the current waveforms why it is critical to
keep the high switching current paths to a small physical
size. High electric and magnetic fields will radiate from
these loops just as radio stations transmit signals. The
output capacitor ground should return to the negative
terminal of the input capacitor and not share a common
ground path with any switched current paths. The left
half of the circuit gives rise to the noise generated by
a switching regulator. The ground terminations of the
synchronous MOSFETs and Schottky diodes should
return to the bottom plate(s) of the input capacitor(s)
with a short isolated PC trace since very high switched
currents are present. External OPTI-LOOP ? compensa-
tion allows overcompensation for PC layouts which are
not optimized, but this is not the recommended design
procedure.
3856f
相关PDF资料 |
PDF描述 |
|---|---|
| EYM25DRSS | CONN EDGECARD 50POS DIP .156 SLD |
| VE-254-EW-F2 | CONVERTER MOD DC/DC 48V 100W |
| EGM25DRSS | CONN EDGECARD 50POS DIP .156 SLD |
| LTC3866EFE#TRPBF | IC REG CTRLR BUCK PWM CM 24TSSOP |
| EEM43DREF | CONN EDGECARD 86POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3856IFE#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 38TFSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3856IFE#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 38TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3856IUH#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 32WFQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3856IUH#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3857EGN-1#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
发布紧急采购，3分钟左右您将得到回复。