- 您现在的位置：买卖IC网 > PDF目录1834 > LTC4110EUHF#TRPBF (Linear Technology)IC BATTERY BACKUP MANAGER 38-QFN PDF资料下载
参数资料
| 型号： | LTC4110EUHF#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 20/52页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY BACKUP MANAGER 38-QFN |
| 标准包装： | 2,500 |
| 功能： | 备份管理 |
| 电池化学： | 铅酸，锂离子，锂聚合物，镍镉，镍氢，超级电容器 |
| 电源电压： | 4.5 V ~ 19 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
LTC4110
OPERATION
? The CAL_START bit in the BBuControl() register is set.
The LTC4110 enters the calibration state.
? The battery thermistor is registering RES_OR. The
LTC4110 enters the reset state.
LEAD ACID BATTERY CHARGE MODE
The charger is programmed for lead acid batteries by con-
necting the TYPE pin to a voltage derived from the V REF
pin resistor divider of nominally 0.5 ? V REF . During charge,
the LTC4110 operates as a high ef?ciency, synchronous,
PWM ?yback battery charger with constant current and
constant ?oat voltage regions of operation. The constant-
charge current is programmed by the combination of a
resistor (R CHG ) from the I CHG pin to ground, a battery
current sense resistor (R SNS ) and CSP/CSN pin resistors.
The ?oat voltage is programmed to one of four values
(4.7V, 7.05V, 11.75V, 14.1V) depending on the number of
series cells (2, 3, 5 or 6) using the SELC pin and can be
adjusted ±0.15V/cell with the V CHG pin.
A new charge cycle begins with the charger in the bulk
charge current limited state. In this state, the charger is
a current source providing a constant charge rate and the
CHGb (GPIO1 pin) is forced low. No time limits are placed
upon lead acid battery charge. The charger monitors the
battery voltage and as it reaches the ?oat voltage the
charger begins its ?oat charge. While in ?oat, the charge
current diminishes as the battery accepts charge. Float
voltage temperature compensation and temperature fault
monitoring, if desired, are accomplished with an external
thermistor network.
Charge is active when the supply input is present as sensed
by the DCDIV pin and DCIN above UVLO, thermistor
temperature is ideal according to the thermistor monitor
circuit (see SafetySignal Decoder) and the charge register
bit CHARGE_INHIBIT is cleared. Soft-start ramps the charge
current at a rate set by the capacitor on the I TH pin. When
charge begins, the CHGb (GPIO1 pin) status output is
forced to GND. At any time charge can be forced to stop by
pulling the SHDN pin high or setting the CHARGE_INHIBIT
bit high through the SMBus.
If the battery voltage exceeds 107.5% (V BOV ) of the pro-
grammed ?oat voltage during any stage of charge, the
charger pauses until the voltage drops below the hysteresis
(V BOVH ). No fault is indicated.
An optional external NTC thermistor network can be used
to provide an adjustable negative TC for the ?oat voltage,
monitor battery temperature and to detect battery pres-
ence. If the thermistor value indicates a hot temperature,
voltage falling to V HOT on THB pin, charge current is halted,
CHG_FLTb (GPIO3 pin) is forced low and the CHG_FLT bit
will be set high. CHGb (GPIO1 pin) and CHG_STATE_0 and
CHG_STATE_1 register bits will not be affected. When the
thermistor value returns to ideal when the voltage exceeds
V HOT +V HOTH on THB pin, charge resumes CHG_FLTb
(GPIO3 pin) returns to high impedance and the CHG_FLT
bit will be reset low. An open thermistor indicates an
over-range which is considered absence of a battery.
Low temperature is not monitored. However, since bat-
tery removal detection looks at the thermistor for a high
resistance (V REM on THB pin), extremely cold temperatures
may result in an indication of battery absence. To defeat
the temperature monitoring register, replace the thermis-
tor with a resistor to indicate normal battery temperature.
When a thermistor is not used the resistor circuit must be
routed through the battery connector if battery presence
detection is required.
BATTERY CALIBRATION MODE
Figure 6 shows the LTC4110 in battery calibration mode and
the corresponding PowerPath enabled. During calibration,
the host CPU can calibrate a gas gauge or verify the battery’s
ability to support a load by use of a low heat producing
method. Calibration requires a host to communicate over
a SMBus. In the low heat method, a synchronous PWM
?yback charger is used in reverse to discharge the battery
with a programmable constant-current into the system
load thereby saving space and eliminating heat generation
compared with resistive loads. Protection circuits prevent
accidental overdrive back into the power source if the
system load is insuf?cient. The constant-charge current
is programmed by the combination of a resistor (R CAL )
from the I CAL pin to ground, a battery current sense resis-
tor (R SNS(BAT) ) and CSP/CSN pin resistors. Calibration is
initiated by setting the CAL_START bit in the BBuControl()
register. The CAL_ON bit in the BBuStatus() register will
4110fb
20
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4150IMS#TRPBF | IC COUNTER/GAUGE GAS/BATT 10MSOP |
| LTC4155IUFD#TRPBF | IC I2C POWER MANAGER DUAL 28QFN |
| LTC4160EUDC-1#TRPBF | IC SWITCH POWER MANAGER 20-QFN |
| LTC4410ES6#TRPBF | IC POWER MANAGER USB TSOT23-6 |
| LTC4411ES5#TRMPBF | IC IDEAL DIODE LOW LOSS TSOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4120IUD#PBF | 制造商:Linear Technology 功能描述:BATTERY CHARGER, 400MA, QFN-16, Battery Type:Li-Ion, Li-Polymer, Input Voltage:4 |
| LTC4150 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage, High-Side Current Sense |
| LTC4150_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Coulomb Counter/ Battery Gas Gauge |
| LTC4150CMS | 功能描述:IC COUNTER/GAUGE GAS/BATT 10MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4150CMS#PBF | 功能描述:IC COUNTER/GAUGE GAS/BATT 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
发布紧急采购，3分钟左右您将得到回复。