- 您现在的位置：买卖IC网 > PDF目录1834 > LTC4110EUHF#TRPBF (Linear Technology)IC BATTERY BACKUP MANAGER 38-QFN PDF资料下载
参数资料
| 型号： | LTC4110EUHF#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 29/52页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY BACKUP MANAGER 38-QFN |
| 标准包装： | 2,500 |
| 功能： | 备份管理 |
| 电池化学： | 铅酸，锂离子，锂聚合物，镍镉，镍氢，超级电容器 |
| 电源电压： | 4.5 V ~ 19 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
LTC4110
OPERATION
Table 6. Register Command Set Descriptions (XxxxXxxx() – Register Byte, XXXXXXXX – Status Bit)
LABEL
DESCRIPTION
ChargerStatus() – Read Only. The SMBus host uses this command to read the LTC4110’s charge status bits.
AC_PRESENT
BATTERY_PRESENT
ALARM_INHIBITED
RES_UR
RES_HOT
RES_COLD
RES_OR
LEVEL:3/LEVEL:2
CHARGE_INHIBITED
Set to 1 when suf?cient input voltage (DCDIV > V AC + V ACH and DCIN above UVLO) available and switches load from
battery to main supply. Zero indicates backup mode engaged.
BATTERY_PRESENT is set if a battery is present, otherwise it is cleared. The LTC4110 uses the SafetySignal to
determine battery presence. If the LTC4110 detects a RES_OR condition, the BATTERY_PRESENT bit is cleared
immediately. The LTC4110 will not set the BATTERY_PRESENT bit until it successfully samples the SafetySignal
twice and does not detect a RES_OR condition on either sampling. If AC is not present (DCDIV < V AC or DCIN
below UVLO), this bit may not be set for up to one-half second after the battery is connected to the SafetySignal.
The ChargingCurrent() and ChargingVoltage() register values are immediately cleared whenever this bit is cleared.
Charging will never be allowed if this bit is cleared.
ALARM_INHIBITED bit is set if a valid AlarmWarning() message has been received and charging is inhibited as a
result. This bit is cleared if POR_RESET is set, both ChargingVoltage() and ChargingCurrent() are rewritten to the
LTC4110, the power is removed (DCDIV < V AC or DCIN below UVLO), the SHDN pin is set high, or if a battery is
removed.
Set to 1 when NTC pin is below 500 Ω typical. This bit is never set when TYPE pin selects SLA battery..
The RES_HOT bit is set only when the SafetySignal resistance is less than 3k Ω (3.1kΩ for SLA) typical, which
indicates a hot battery. The RES_HOT bit will be set whenever the RES_UR bit is set.
The RES_COLD bit is set only when the SafetySignal resistance value is greater than 30k Ω typical. The SafetySignal
indicates a cold battery. The RES_COLD bit will be set whenever the RES_OR bit is set. This bit is the same as
RES_OR for SLA.
The RES_OR bit is set when the SafetySignal resistance value is above 100k Ω (114kΩ for SLA) typical. The
SafetySiganl indicates an open circuit.
The LTC4110 always reports itself as a Level 2 Smart Battery Charger.
Indicates charge inhibited is enabled when set to a one. This is a duplicate of the CHARGE_INHIBIT bit in the
BBuStatus() register.
ChargingCurrent() – Write Only. The battery, system host or other master device sends the desired charging current to the LTC4110.
ChargingCurrent()
LTC4110 only monitors for zero or non-zero values. A value of zero will stop the charger. A non-zero value here, and
for ChargingVoltage(), will restart the charger.
ChargingVoltage() – Write Only. The Battery, System Host or other master device sends the desired charging voltage to the LTC4110.
ChargingVoltage()
LTC4110 only monitors for zero or non-zero values. A value of zero will stop the charger. A non-zero value here, and
for ChargingCurrent(), will restart the charger.
AlarmWarning() – Write Only. The Smart Battery, acting as a bus master device, sends the AlarmWarning() message to the LTC4110 to notify it that one or
more alarm conditions exist. Alarm indications are encoded as bit ?elds in the battery’s status register, which is then sent to the LTC4110 by this function.
Only the OVER_CHARGED_ALARM, TERMINATE_CHARGE_ALARM,RESERVED_ALARM, OVER_TEMP_ALARM and TERMINATE_DISCHARGE_ALARM
bits are supported by the LTC4110. The ALARM_INHIBITED bit in the ChargerStatus() register indicates whether a charging process or a calibration
process was halted by a write to this register.
OVER_CHARGED_ALARM
TERMINATE_CHARGE_ALARM
RESERVED_ALARM
Set to one indicates battery has been overcharged and stops charge. Setting this bit will only stop a charging
process (default = zero).
Set to one indicates battery requesting charge termination. Setting this bit will only stop a charging process (default
= zero).
Set to one for reserved alarm condition. Setting this bit will stop both a calibration process and a charging process
(default = zero).
4110fb
29
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4150IMS#TRPBF | IC COUNTER/GAUGE GAS/BATT 10MSOP |
| LTC4155IUFD#TRPBF | IC I2C POWER MANAGER DUAL 28QFN |
| LTC4160EUDC-1#TRPBF | IC SWITCH POWER MANAGER 20-QFN |
| LTC4410ES6#TRPBF | IC POWER MANAGER USB TSOT23-6 |
| LTC4411ES5#TRMPBF | IC IDEAL DIODE LOW LOSS TSOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4120IUD#PBF | 制造商:Linear Technology 功能描述:BATTERY CHARGER, 400MA, QFN-16, Battery Type:Li-Ion, Li-Polymer, Input Voltage:4 |
| LTC4150 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage, High-Side Current Sense |
| LTC4150_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Coulomb Counter/ Battery Gas Gauge |
| LTC4150CMS | 功能描述:IC COUNTER/GAUGE GAS/BATT 10MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4150CMS#PBF | 功能描述:IC COUNTER/GAUGE GAS/BATT 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
发布紧急采购，3分钟左右您将得到回复。