参数资料
型号: M30201F4T-FP
元件分类: 微控制器/微处理器
英文描述: 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP56
封装: PLASTIC, QFP-56
文件页数: 12/158页
文件大小: 1633K
代理商: M30201F4T-FP
109
Under
development
Mitsubishi microcomputers
M30201 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Usage precaution
Timer X (pulse width modulation mode)
(1) The timer Xi interrupt request bit becomes “1” if setting operation mode of the timer in compliance with
any of the following procedures:
Selecting PWM mode after reset.
Changing operation mode from timer mode to PWM mode.
Changing operation mode from event counter mode to PWM mode.
Therefore, to use timer Xi interrupt (interrupt request bit), set timer Xi interrupt request bit to “0” after
the above listed changes have been made.
(2) Setting the count start flag to “0” while PWM pulses are being output causes the counter to stop
counting. If the TXiINOUT pin is outputting an “H” level in this instance, the output level goes to “L”, and
the timer Xi interrupt request bit goes to “1”. If the TXiINOUT pin is outputting an “L” level in this
instance, the level does not change, and the timer Xi interrupt request bit does not becomes “1”.
Timer X (pulse period/pulse width measurement mode)
(1) If changing the measurement mode select bit is set after a count is started, the timer Xi interrupt
request bit goes to “1”.
(2) When the first effective edge is input after a count is started, an indeterminate value is transferred to
the reload register. At this time, timer Xi interrupt request is not generated.
A-D Converter
(1) Write to each bit (except bit 6) of A-D control register 0, to each bit of A-D control register 1, and to bit
0 of A-D control register 2 when A-D conversion is stopped (before a trigger occurs).
In particular, when the Vref connection bit is changed from “0” to “1”, start A-D conversion after an
elapse of 1 ms or longer.
(2) When changing A-D operation mode, select analog input pin again.
(3) Using one-shot mode or single sweep mode
Read the correspondence A-D register after confirming A-D conversion is finished. (It is known by A-
D conversion interrupt request bit.)
(4) Using repeat mode, repeat sweep mode 0 or repeat sweep mode 1
Use the undivided main clock as the internal CPU clock.
Stop Mode and Wait Mode
____________
(1) When returning from stop mode by hardware reset, RESET pin must be set to “L” level until main clock
oscillation is stabilized.
(2) When shifting to WAIT mode or STOP mode, the program stops after reading 8 bytes from the WAIT
instruction and the instruction that sets all clock stop bits to “1” in the instruction queue. Therefore,
insert a minimum of 8 NOPs after the WAIT instruction and the instruction that sets all clock stop bits
to “1”.
相关PDF资料
PDF描述
M38259EFFS 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQCC100
M38259EF-XXXFP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP100
M37471E8SS 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CDIP42
M38503E6FP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO42
M37212M6-XXXFP 8-BIT, MROM, MICROCONTROLLER, PQFP80
相关代理商/技术参数
参数描述
M30201F4T-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY
M30201F4T-XXXSP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY
M30201F4-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY
M30201F4-XXXSP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY
M30201F6 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER